79680518900 Kenmore Dryer - Instructions

Simple replacement

Just unscrewed the original lock and screwed the new one on it was very easy

Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled

Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.

FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.

Followed video provided on site

I assumed this was a belt problem. Ordered the belt and followed the excellent screw by screw instructional YouTube provided by PartSelect. In fact, I probably would not have attempted the repair, until I watched the video and was reassured that I could do it. When I got the front panel off, the problem was obvious. There was a dishrag stuck in the blower. Didn't need the belt, but the video was sure worth the price of the part (~$17). Mr. Appliance charges $109 to DIAGNOSE the problem! This was way easier than dealing with them, especially during a pandemic near the holidays.

To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson

My cleaning lady brought her handy husband over Saturday to help me. The only tool we used was a Phillips-head screwdriver. I went online earlier in the week and found a good video put out by Repair Clinic and another one I found on You-tube on how to disassemble the dryer. After watching several times, I knew I could do it. We worked together, I cut my hand on the inside edge of the control panel, but, when I hit a snag, we watched that part of the video again and worked right through. Replaced the Thermistor, NTC first, not a problem. Then the Heater Assembly, not too difficult. I couldn't find where one of the remaining parts went, so, we reassembled the dryer and gave it a try. Worked like a charm. We did remove a lot of lint from inside the cabinet and around the felt liner on either end of the drum. It works like it did when it was brand new. Highly recommend to work with someone, so, you don't get frustrated. I am 65 years old and this was a no brainer for me, although I am somewhat mechanically inclined. Very empowering to accomplish this repair. Just follow the video.

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

Really easy to do! Unscrewed 4 screws, pulled flap on bottom of inside guide out. Then gently shake assembly to loosen from dryer and pull up and out! Then based on the assembly can replace front or back or both. They snap together! Put assembly replacement back in and close flap and secure in place with the four screws.

R&R new lint filter.Old filter appears to have been made improperly and the out frame was warped raising the cormer that kept catching the clothes.

You will need a helper. Dismantle the Dryer: Remove the screws that hold the top cover, front control panel, front door and front panel. Release the V-Belt under the drum. Remove the Drum. Removed and replace the 2 Front roller assemblies - these were completely worn. Replaced the 2 rear rollers (did not replace the rear roller axels as these were more difficult to remove and they were in good shape) and the V-Belt while I had the whole thing open. Use a shop vac and cleaned up the whole unit. It is so nice and quiet now.

Seemed to be shutting off on the safety thermostat so I replaced them all. Works.