11068082701 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donna from CARY, NC
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from BENZONIA, MI
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screen ripped
Dropped new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Anderson, IN
- Parts Used:
- WP3390719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer electrically dead
Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from ETTERS, PA
- Parts Used:
- WP8544737
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The fan wheel had a blade break off, my bad.
I went on the site and found the part I needed and then watched the video explaining how to dismantle, replace the part, and put the dryer back together. It was easy, especially with the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERNST from FLOSSMOOR, IL
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
broken door catch
pushed the broken catch into the door and snapped the new one back in. Works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from SAINT LOUIS, MO
- Parts Used:
- WP8544771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
No heat
You tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from AUBURN, NY
- Parts Used:
- WP8544771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Heater element died
Pretty easy repair and I am not very handy. I believe they engineer these machines so you hire someone to do the job. They could place that part in an area where it is easier to get to, like a door on the side or something
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henri from SILER CITY, NC
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Plastic part in door catch was broken so door would not lock to allow the dryer to operate
I tried to remove the part with pliers but could not remove it so I removed the screws that hold the front part of the door. I took the front part off, removed the broken plastic and then lifted on side of the catch so that the bottom of the front part came thru the door and then was able to remove the door latch. The installation of the new part took about 15 seconds to put in by pushing it into the opening where the broken part was removed. I put the front part of the door back and put the screws back and the dryer works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DW from ALVIN, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
F-26 Fault message
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Thank You.
DW Pranger
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from VILLA RICA, GA
- Parts Used:
- WP3390719
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dryer would power up but not run.
Removed front of dryer. Located thermal fuse, replaced blown thermal fuse. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from St. Louis, MO
- Parts Used:
- WPW10512946
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ORANGE, TX
- Parts Used:
- WP8544771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
No heat!!
Remove top, remove two front panels, remove rear panel to access drive motor release tensioner. Remove drum to access to heating element enclosure. Replace and reinstall after vacuuming all accumulated lent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LANA from INDIANAPOLIS, IN
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Door would not clisr
Had to force the old door catch out using the putty knife didn't work. Worked on it until I finally forced it out.
Was this instruction helpful to you?
Thank you for voting!
Start button failed to keep dryer running; no heat
Dryer is still in pieces after two weeks, dependent upon my time and ability to work on the project. I usually dry my clothes on an outside line, anyway. I especially appreciate Steve's videos demonstrating step-by-step procedures for disassembly, part installation, and reassembly. Very thorough. I timed each presentation---five minutes for one, less than ten for the other. I watched the videos several times and took notes, so I would have the procedures in front of me while working on the unit at the other end of the house, I'm 77, forgetful. When I disassembled my unit, I noticed several rusted areas, so decided not to complete the project until I could get to the store for paint. As a primary care-giver for a severely dementiated 79-year Old Lady, I have to arrange for a relief to go shopping. That's why the machine is still in pieces. Got the paint, though, so back to work---eventually. When I disassembled the dryer, tucked away in the bottom was a very informative TECH SHEET, the discovery of which ticked me off that it wasn't provided with the owner's manual. At the bottom it says, "For Service Technicians' Use Only." In my house, I'm the "...Service Technician...," chief cook and bottle washer, launderer and litter box attendant.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnical from Napanoch, NY
- Parts Used:
- 280148
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
My dryer was not getting hot.
The first thing I did was to watch the video from Part select on How to change thermostat cut off switch and the high limit thermostat fuse.I did not have a meter reader I just brought the thermostat cut off kit for about $ 32.00 dollars from part select and replace both part's and my dryer still was not getting hot so back to part select video's I looked up the video on replacing the heater element and I ordered one for about $ 97.00 with shipping I replaced it and put it back together and it worked it took just a few hours . I would like to give Avery special thank to part select for the video help and for having the parts for a great price again thank you so much.
Was this instruction helpful to you?
Thank you for voting!