11087572601 Kenmore Dryer - Instructions

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.

Followed video step by step. Perfect instructions. I’d only add that you should get and wear mechanics gloves. My hands got torn up by the sharp metal edges taking apart and putting it back together. Ouch!!
So happy with Partselect though. Super fast shipping and a perfect instructional video. Thanks!!

P.S. Wear gloves!!!

Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge would be thru the roof.

At first, my dryer would just make a clicking noise but would not start. After some research, I unplugged it to try to 'reset' it and after that, I noticed the F01 error. Some quick research on the internet you can find the source of the error is a failed machine board. Some DYI people soldered the part where the connection broke but, I chose to just buy the new part. I was pretty confident where the error was and did not want to waste time and the cost of a repair man visit. I followed the instructions on the most thorough YouTube video and removed the top of the dryer, took pictures of the control board wires and began the removal process. The insertion fo the new board took about 1 minute. All in all, the physical work took my husband and I about 10 minutes. Research was about an hour and I had the part shipped overnight. This website has saved me hundred of dollars and lots of wasted time trying to find a repair man when Covid has made it difficult to get anyone to your house. Our washer sprung a leak during the initial lockdown and we were able to fix that ourselves as well.
My only comment about the part is that the chime at the end of the cycle is very different. I have yet to find out if I can change that but it is not too bothersome.
I love this website and its products!

I don't have instructions ,I watched the link provided by parts select. I just wanted to say I have never been a wiz at home repairs.it took so long because I am 62 with autheritis in my hands and the dryer had to be taken down to a motor and a base but I took the time to clean every inch of the dryer scary to see so much dryer lint inside the dryer.i am just going to say if I can do it anybody could fix their own dryer ,just take your time ,let your hands take a break. And keep the repair instructions close by

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.

I replaced both the door strike and the female portion. The door still does not close tightly. Heavy, wet items also knock the door open.

Just replaced the old lint filter.

1 screw to replace.

Pulled the lower front panel located thermal switch pulled 2 wires removed 2 small bolts pulled switch out set meter to ohms scale and tested between the 2 terminals it hailed the test I reversed for installation of new switch

Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retainer clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.

After determining that the dryer motor was the issue, I wrote down the part number and logged on to partselect.com website.

I input the number into the search box and there was the exact motor I needed.

The correct part showed up in a timely manner and the pricing was very fair.

I disassembled the dryer, removed the old motor and reinstalled the new motor within about 30 minutes.

Key point was to read the instructions first and then reconnect the wiring to the new motor. The new motor has the switch install in a different spot on the motor so be careful to follow the instructions but, the instructions were very clear and connections were very simple.

I also did some preventive maintenance while I was in the unit by cleaning out any remaining lint from the heater unit and surrounding areas, that took about 30 minutes. Reassembling was a snap and I turned on the gas, plugged it in and........SUCCESS! Total time of repair and cleaning was about an hour.

I had a load of laundry ready to go and put the new motor right to work. It has been non-stop drying and thanks to Part Select for getting everything right the first time. It has been a positive experience and I will tell others about the website if they have similar problems. Thanks again for a success story and dry clothing.

I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.

I disassembled the dryer, replaced the pulley (which was noisy), and the belt.reassembled, only to find out that the drum would not turn freely. checked all my procedures and kept having the same problem. Finally after 3 frustrating hours, I took the back off and noticed that idler arm was tight against the motor shaft, because the too short belt didn't allow for the clearance needed. Had too take everything apart ,another hour, went and found one at our local repair shop, reinstalled everything , after another two hours runs fine. would appreciate a refund. And please check your part numbers in the future. Would hate to have someone else go through what i experienced.