11061252011 Kenmore Dryer - Instructions

We were able to look at the diagram of the dryer to figure out how to access the part and then replace it. Fantastic! Your site is wonderful. The suggestion for the repair for not starting was right on the mark. The parts came very quickly, as well.

The dryer motor quit working. Learned, if you are changing one that is old, get the blower wheel fan too! I could not break mine loose from the motor shaft, and had to bust it off.

To un-screw the blower wheel fan from the motor shaft: from the front of the dryer, grab the plastic fan on the back of the motor with an adjustable wrench, and the motor shaft on the front of the motor with vice grips. Turn the motor shaft CLOCKWISE holding the fan still to un-screw the fan. If you have to remove the pulley, grab the shaft and turn the pulley COUNTERCLOCKWISE with a wrench.

Just make sure to pay attention to the orientation of the new motor in the instructions. If you match the old motor, it will not fit. It is all spelled out in the directions.

First I removed the two wires from the overheat fuse, then I removed the 1 screw and removed the fuse. I installed the new overheat fuse and attached with 1 screw, then reconnected the 2 wires. I attached the back cover with two screws and tested the dryer. It was working, so I finished attaching the back with the remaining screws and exhaust duct. Installation complete.
Note: Two weeks later I had to replace the fuse again because I had checked the duct pipe and exhaust chute, but not the bottom at the fan. Be sure to remove the flat exhaust duct and check for bulid-up at the bottom under the fan.

First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to glue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!

First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Piece of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!

Once I unpluged the dryer and then removed the back cover, I located the heating unit and then removed the thermostat. Once that was done, I installed the new thermostat and connected the wires. I tested the dryer to make sure that it would heat. Then I replaced the back cover.

I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....

Followed video on Parts Select site for comparable model showing roller and drive belt replacement.

The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.

Came to Parts Select. Looked for door switch. Read what other people did. Part came in a few days took a few minutes to take old switch out (had to pry the plastic connection apart with little thin screwdriver). Everything was easy

I watched the installation video on both parts before I purchased them and it was a piece-of-cake after that.

Purchased thermal cut off kit but only replaced the top most thermostat. There were some extra wires wired into the bottom thermostat, that were not described on the video or any other repair user posts. It checked fine on my multimeter anyway.

Lint screen on my 30-year dryer was torn. Ordered the new screen here with just the part number, fits well. Very helpful website.

PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.