79679272000 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- EDWARD from KNG OF PRUSSA, PA
- Parts Used:
- 5318EL3001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Igniter burned out
Completely had to dismantle the dryer to get to the igniter.
The screw holding the igniter is a SOB to get at for extraction, and even worse putting back.,
The screw holding the igniter is a SOB to get at for extraction, and even worse putting back.,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gabriella from Lexington, VA
- Parts Used:
- 5231EL1001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer lint filter lining was falling apart and lint was not being filtered
Ordered a new Dryer Lint Filter Assembly that fit my LG electric dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from ATASCADERO, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was making a terrible sound.
An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from GOLDFIELD, NV
- Parts Used:
- 6500EL3001A, 5318EL3001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Persistent smell of propane despite multiple duct cleanings.
Despite the young age of this dryer, and failure of all the other trials to fix the problem, I figured maybe the igniter is the problem. Ordered one. Followed a U tube video to take the unit apart. Noticed immediately that there was lots of lint pretty much everywhere inside the cabinet. Come to find that the blower and the vent had never been connected, with about two inches gap. So, some of the exhaust was going out the vent hose, but lots was not. In fact, lint had coated the propane jet and the air mixer assembly. Replacing the igniter was not particularly difficult, once the dryer was in lots of pieces. I did not test the igniter before replacing it. I did connect the vent outlet to the blower and secured it. End result was a perfectly functioning unit and a happy wife. I don't recall reading about this as a possible cause of propane odor and failure of the unit to heat up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joani from BONNER SPGS, KS
- Parts Used:
- 4948EL4001B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
LP to Natural Gas
The installation of the gas orifice was actually simple. Unscrew the old orifice and screw in the correct orifice. Tricky part of the process was accessing the area of the gas valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Tavares, FL
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Had an issue with the dryer not drying the clothes in the allotted time and turning the dryer off. I knew it was still getting heat so I googled the issue with suggestions.
I watched a YouTube video with how to take the dryer apart and remove the sensors. I followed the what the instructions were removing the top of the dryer and then the front panel. Once that was removed it was a matter of removing 7 more screws and the lint collector piece came off. Popped the sensor pieces out. Cleaned the inside of the dryer and reinstalled a total of 5 parts and dryer is working fine and the clothes are drying in the allotted time it use to take.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RIVERSIDE, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Loud rumbling noise
Followed video provided on site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omar from SILVER CITY, NM
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
CHANGED OUT MOTOR
FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from CUDAHY, WI
- Parts Used:
- 6323EL2001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
no heat
To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D Michael from Plymouth, IN
- Parts Used:
- 4581EL2002L, 4400EL2001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
noise when you ran dryer
Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from DAWSONVILLE, GA
- Parts Used:
- 3911EZ9131X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Install aftermarket side vent kit
I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Whittier, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Thumping sound when dryer is on.
I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Marriottsville, MD
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Changed mottor
I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Boise, ID
- Parts Used:
- AJQ75298102
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Hole in drum
Found YouTube video followed it closely and did extensive cleaning. The lint on the felt of the drum was causing a rough rotation as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Inland Commercial Appliance from Moreno Valley, CA
- Parts Used:
- AGM30045804, AGM30045804, 6931EL3002M, 6500EL3001A, 6323EL2001B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Not heating correctly
Removed Top, then front and drum. Parts easy to access once drum is out. Recommend reading up on drum replacement. Would appear that all repairs will require taking it out.
Was this instruction helpful to you?
Thank you for voting!