11076408450 Kenmore Dryer - Instructions

Pull out the old lint filter unit; push in the new one.

Opened new package took item out and put it on the slot where the old filter was. Easy as pie. My dryer is 46 years old and works just fine.

Unplug unit first.
Took the front cover off the front of dryer below the door.

i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.

Removed the dryer's back panel and took a look. Had no idea what to do next, so I read up on it. Partselect was extremely helpful to me, the exploded views with the part numbers called out were particularly helpful. So I determined it was the thermal fuse. Unscrewed the screw holding in the fuse and disconnected the electrical supply. New fuse went in really easily. Job took a lot longer than it had to cause since I was in there, I cleaned out the dryer really good.

Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!

Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

Ordered the motor with pulley and blower wheel in case the wheel did not come free from the motor.
Took out the lint screen, took off the top and disconnected the wires for the door switch, took off the front.
Remove the idler poi and the belt and then removed the drum.
I read in other repair YouTube videos, the blower wheel sometimes is so seized onto the motor axle that you have to remove the wheel by cutting it off.
Yes, ours seized!
Cut off the motor axle with a hacksaw and then the motor and the wheel were free. This was not an issue since I had purchased both the motor and the wheel which I recommend doing anyway. Our dryer over 25 years old and it does not have many electrical components, which I love. We removed the parts put in the new parts. Follow the wiring diagram to get the new motor hooked up.
Then I replaced the drum support rollers, which were a snap and then we put it all back together.
We added an extra step because we had to takeoff the back of the dryer to gain access to the blower. It turned out to be a good thing since years of lint have been trapped at the bottom of the lint chute.
I cleaned everything, washed everything and put it all back together and it purrs like a kitten.
Took us about 2 1/2 hours total since we are very cautious and slow as we didn’t want to break things.
I am very happy with the end result and hopefully it will last another 25 years!
Parts were spot on and worked perfectly.
Much more economical than buying a new dryer for $750-$1000.

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

I followed the video. So easy..

The first step was to check the electrical supply to make sure I had power 120 volt. I unplugged the dryer and turned off the gas supply and turned the dryer around so I could have access to the back panel removed panel to access the wiring harness and safety thermostats. All switches and wire checked good with my ohmmeter .I pulled off the front kick panel and checked the electrical schematic and found the door switch was in the circuit to check it I had to lift up the top and pop out the front to access the door switch checked switch and found it defective. Replaced switch vacuumed out dryer and vent reassembled dryer and all worked good.