11060094990 Kenmore Dryer - Instructions

My Whirlpool dryer had no heat. I removed the back panel and within minutes diagnosed the problem to a blown thermal cut-off fuse. I ordered a thermal cut-off kit on a Sunday night and had the parts at 7:30am Wednesday morning. Total time for diagnosing and repair was no more than 15 minutes. PartSelect saved me a ton of money and aggravation!!! AWESOME!!!!

Gary

Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge would be thru the roof.

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.

Was not sure what was wrong but the Part Select site allowed us to view other repair issues and solutions. We ordered the kit, it arrived the next day (how is that possible) and easily put the parts in and chaching...money saved and dryer works better than ever. THANKS PartSelect, we give you an eleven and we will recommend you to everyone.

Just replaced the old lint filter.

The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.

Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retainer clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.

I disassembled the dryer, replaced the pulley (which was noisy), and the belt.reassembled, only to find out that the drum would not turn freely. checked all my procedures and kept having the same problem. Finally after 3 frustrating hours, I took the back off and noticed that idler arm was tight against the motor shaft, because the too short belt didn't allow for the clearance needed. Had too take everything apart ,another hour, went and found one at our local repair shop, reinstalled everything , after another two hours runs fine. would appreciate a refund. And please check your part numbers in the future. Would hate to have someone else go through what i experienced.

After determining that the dryer motor was the issue, I wrote down the part number and logged on to partselect.com website.

I input the number into the search box and there was the exact motor I needed.

The correct part showed up in a timely manner and the pricing was very fair.

I disassembled the dryer, removed the old motor and reinstalled the new motor within about 30 minutes.

Key point was to read the instructions first and then reconnect the wiring to the new motor. The new motor has the switch install in a different spot on the motor so be careful to follow the instructions but, the instructions were very clear and connections were very simple.

I also did some preventive maintenance while I was in the unit by cleaning out any remaining lint from the heater unit and surrounding areas, that took about 30 minutes. Reassembling was a snap and I turned on the gas, plugged it in and........SUCCESS! Total time of repair and cleaning was about an hour.

I had a load of laundry ready to go and put the new motor right to work. It has been non-stop drying and thanks to Part Select for getting everything right the first time. It has been a positive experience and I will tell others about the website if they have similar problems. Thanks again for a success story and dry clothing.

I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.

Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.

I saw some videos suggesting you remove the back panel.Then I saw a video where only the kick plate was removed and the element was removed that way.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant amount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.

Replaced the heating element. Took the front lower panel off, 2 screws one on each end, removed cover on left side over blower 3 screws and removed cover lower right side over heating element 2 screws. Removed 6 wires plugged into heating element cover, turned heater element cover counter clockwise and pulled out. Removed 1 screw holding heating element inside of cover, pulled out heating element. Replaced heating element back in cover putting screw back in to hold it. Put heating element and cover into hole in back of dryer turning clockwise to secure. Then put cover holding heating element over the front of it and secured with 2 screws. Put blower cover back secured with the 3 screws and put the front cover back on securing with 2 screws. dryer is heating better than ever.

Removed the back of the dryer about 8 screws. Removed the Thermostat 250 F and replaced with new. Dries a load of clothes in one cycle on medium. Not bad for a 16 dollar part. I am a computer tech and I am used to taking computers a part but I think most people that are in anyway mechanically inclined and can look at a diagram could do this and save yourself a lot of money.