11078690200 Kenmore Dryer - Instructions

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

Disassembled dryer, removed tumbler, replaced drum support rollers

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.

I followed your short video and found it very easy to do

Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.

removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

Replaced lid switch, but problem still continued.

Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.