1106307803 Kenmore Dryer - Instructions

It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

This was a classic easy repair and I am sure saved us bundles on a service call.

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

take the old latch out and pop the new one in. Your repair kit worked perfect.

i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.

I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.

The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen the two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!

The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!