11096592410 Kenmore Dryer - Instructions

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

With the help of YouTube, I was able to watch videos of how to disassemble and reassemble the dryer. I watched a video showing where the Thermal fuse and Thermostat was located as well as how to test them with a meter. I watched another video showing how to replace the drum belt, showing step by step instructions. Without YouTube it would have been a whole different story!

Just replaced part

Turned off my circuit breaker first. Removed back panel with a 1/4 nut driver. Replaced the dryer fuse first. Very easy but did not fix the problem. Watched how to videos to narrow down the parts I might need. Purchased the thermal cut off kit. Installed the High limit thermostat first. Tested the dryer, no dice. Finally installed the Thermal cutoff. BAM!! I have heat. Since this is an older dryer I did need to use some WD40 to loosen some of the connections. Total cost of parts including tax and quick delivery was $48.30. Fantastic. My old man told me it was unfixable. He was wrong. I WIN. This site is a great teaching site. Thank you!

Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum, let sit a few minutes. Put everything back together.

Removed the back of the dryer about 8 screws. Removed the Thermostat 250 F and replaced with new. Dries a load of clothes in one cycle on medium. Not bad for a 16 dollar part. I am a computer tech and I am used to taking computers a part but I think most people that are in anyway mechanically inclined and can look at a diagram could do this and save yourself a lot of money.

Just like the video, just followed the video
Thanks,

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.

i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal Fuse blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.

Opened access door, noticed main power wire to heating element was partially melted. This was caused by a bad connection to the drying element, loose. Removed heating element assembly. Cut bad section of wire and added new connection. While doing this the thermostats plastic casing cap came off ! Probably due to exessive heat / resistance from the bad connection. This confirmed why there was no heat. Intalled new thermostat and and am now good to go !

Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel

Unpluged dryer power cord.
Removed lower front panel (two snap clips at top of panel)(Rear panel cannot be removed from this dryer). Removed blower/filter housing (held by two screws). Found blown fuse by using an ohm meter across the fuse terminals with one wire removed - no continuity. When new parts arrived, I removed two wires from fuse and four wires from thermostat. Removed two screws holding fuse and two screws holding thermostat, and removed both parts.
I then reversed the above procedures.
Dryer works great!
Total cost, including shipping, was $47.76