1103402844 Kenmore Dryer - Instructions

MY issue was the heat would cycle up on a fully cold dryer, but if the Dryer stopped for whatever reason or started a sucessive new load, you'd get no heat. I could leave the dryer unplugged for 30 minutes and it would fire back up with heat but would go out shortly, or if lucky might finsh the load.

Most of the repair avenues point towards the cycling thermostat or the flame sensor.

But It was the gas Coils.

It's Been perfect for couple weeks.

Great Site

I took the front dryer panel off by removing 4 screws. I the removed 2 screws from the bracker that secured the 2 valve coils. I unplugged the 2 coils the placed new ones in the exact same position. Fastened the valve coil bracket and replaced the front dryer panel. The dryer worked like new. Thanks!!!

I took the front of the dryer off. The two gas valve coils were right in front. Replaced the two terminal gas valve coil and the secondary coil valve three terminal. Cleaned the inside with shop vac and re-installed the front dryer panel.

UNPLUG Drier
Remove bottom panel 2 screw
Remove 2 connector to coil
remove 2 screws
lift off cover
lift coil s
reverse steps

Unscrewed the front and ran the dryer. The heating coil DID get red hot but the gas DID NOT blow out. Unscrewed the cover over the top of the two coils. Disconected the wire. Replaced coil and cover. SUPER EASY. Its the starting and holding coil which lets the gas shoot out onto the heating filament. $75.00 just for the repair man to come out plus parts, plus labor. Probably saved $200+. All the prints of the parts are on the website so you can see what your changing. TRUST ME....DO IT YOURSELF. You'll be glad you did!!

removed cover removed old coils installed
new coils ,test dryer running great .
thanks partselect.

We followed the on-line video which was very helpful but it took longer for us. But the part didn't fix the problem, so we had to go back on line and research it some more only to find that the more common cure for our problem was the gas coils which were even easier to replace and that did fix the problem.

The first thing to do is to check to be sure the vent is clear. The easiest way to see if this is the problem is to pull the dryed away from the vent and let it vent into the room. Once you have determined that the vent is not the issue, take the front cover off and see what is going on on the inside. To remove the front cover first remove the 4 screws on the inside of the upper cabinet to take off the control panel, I was able to gain access to the screws under the front of the control panel that hold the front cover in place. A couple of electrical connectors later the cover is removed. The coils are easily accessed from in front of the burner by removing the 2 screws that hold the small silver cover over the coil. Once the cover is removed, the coils slide off a short shaft and you can replace the coil by swapping the apporpriate electrical connector for the coil being replaced. The coils are alligned with a small white pin so you can't get it wrong. Replace the covers and fire away.

This repair is easy and saves you a lot of money. This is a great web site, easy to identify the parts you need and the delivery is very fast. Nice Job!!!

The diagrams listed online gave me a the information needed to trouble-shoot which part could be broken. It only took two tries to see which part was out but was significantly cheaper than a repairman. The expediant delivery on parts made down-time a minimal. Very pleased with results.

I ended up taking the entire dryer apart when I didn't need to, and it turns out it wasn't the Igniter Kit in the first place but the thermal fuse in the back. Was pretty simple to repair in any case however.

Pretty much just followed the installation video. Took dryer apart and just put everything back the way it was.

Viewed online then found part and ordered it in, took front off of dryer and cleaned out the dryer. replaced igniter seemed to work but ended up having to replace thermial fuse.

Unplug appliance from power source. Started by simply using screwdriver or steel putty knife to snap up the top corners of the top section of the dryer. It swings open like the hood of a auto. Looked on the back side of the front panel and found small 5/16" bolts on either side. Removed these bolts and lifted up on the front panel to remove the panel. Slide panel out of the way far enough to access the coil kit on the lower front section of the dryer. (The wires going to the door control switch will allow this without unplugging.) May need a helper to hold the dryer drum up out of the way or prop it up as I did with a block of wood so you can easily unplug/re attach the coil wiring. There are two Phillips head screws that hold the coil keeper in place. Remove these two screws, unplug the two coils (front coil has a three connector plug and the one behind it has a two wore plug). the front coil has a small sleeve that I needed to transfer to the new coil in front. Inserted sleeve as it came out of the old coil, slid both coils back in place, replaced coil retainer being careful to line tabs on top of coils so that they lined up in the coil keeper. Replaced screws in coil keeper. Placed front panel back on being careful not to damage the felt liner that the drum spins on. Replaced the two bolts on the inner side of each corner of the front panel. Lowered the top panel and firmly pushed it back down so that the holders went in place. Plugged it up and it worked perfectly.

The hard part of the repair was the diagnosis. I'd take the front off the dryer, start it up, and the flame would fire up. I'd put it all together, start it, hear the flame start, leave, and it would still be running 4 hours later with the clothes wet. Discovered that one of the gas valve coils would work cool and show connectivity, but would stop working shortly after starting. To check the flame and remove the front, remove the door - 1 phillips screw in each hinge, then jiggle up and down pulling away from the dryer. Then, two screws on the opposite side. Facing the opening, grasp front and pull toward you to swing it down. You can temporarily put the door back with the front off while you start it to watch the flame cycle. On regular heat, the flame will run pretty much continuously - in my case, it would start, run for about 1 minute then stop. I assumed it was cycling, but it really runs longer than that. Coil replacement was easy - unplug the dryer, pry off the electrical connectors, remove the two screws on the left which hold the retainer containing the coils Then pull the coils straight up and replace with new ones. The one with three connectors is in front; the one with two connectors in the back. There are plastic tabs on the coils which fit into holes on the retainer. Reassemble in reverse order. To confirm diagnosis, you can use an ohmmeter to check continuity of the coils. The front coil has continuity between the center connector and each of the side connectors. The back coil has continuity between the two connectors. If you're not getting a reading at 1k ohms, it's probably an open coil and needs replacement.

Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.