11086379730 Kenmore Dryer - Instructions

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

Unplugged stove . Removed floor of oven . Easy . Removed the ignitor ,near back of stove under removed floor . .Left it in place to enable locating where wire came through back of stove . Pulled the stove away from wall . Removed back panel of stove . followed ignitor wire to its plug in position . Returned to the front of stove . Inserted new ignitor wire through back wall of stove . Went behind stove , pulled wire through enough to plug new ignitor into proper position . Put back panel onto stove . Pushed stove back against wall . Went back into oven to screw new ignitor into place . Replaced oven floor panels . Put cooking racks back in . Wife proceeded to bake once again .

Unplugged dryer, unscrewed back, and replaced fuse. Easy as 123. Video showed what to do step by step! I am not a handy man, just a woman trying to be money5 smart. Anyone could do this and save on home repairs.

I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.

Went on line and determined the problem was the thermal fuse. Removed the rear panel of the dryer, removed the leads from the thermal fuse, hooked them together and started the dryer. That confirmed the problemwas the existing fuse.Ordered the new thermal fuse, installed the fuse, hooked up the wires and it works finel Very simple fix. About a 10 year old dryer.

removed the rear panel to gain access to the internals of the dryer, removed the one screw that retains the fuse, out with the old and in with the new.
delivery of the part was 2 days sooner than expected.
could not have been a simpler process!

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3

I just lined up the knob with the post and pushed it on, easy!

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

I first watched the helpful video on website. Un- plugged the dryer. I removed the back cover and tested the thermal fuse with the multi meter. Ordered the replacement part. Replaced the Thermal Fuse, and put the back cover back on. This was a very easy fix! It takes longer to remove the back cover of the dryer than it does to replace the fuse. While I had the back cover I used my air compressor to blow out any lint. This dryer is as good as new now. this site fast shipper, Great website.

replaced internal dryer filter housing

The new knob went right on my 33 year old Kenmore dryer. It looks just like the old knob except that it is shiny and new.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Once again part select has come through for me. googled dryer won't start and a video on utube came up. typed my model number in on part select website and followed directions. was easy got part in three business days regular shipping. very pleased with this site.

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!