41792052102 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judy from SAN DIEGO, CA
- Parts Used:
- 137551901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
prolonged drying period and poor lint collection
removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Genevieve from NORTH ANDOVER, MA
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broke and fell into dryer.
All I had to do was pop in the new door catch. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shajauna from Virginia, VA
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken start switch
I watched the video that I saw posted on youtube. My dryer did not have a panel on the back to remove, so the part was very easily accessible. I simply took the old switch off and replaced it with the new one. The most impressive part was receiving the part so quickly. That was awesome! It saved me a trip to the laundromat. I really did not expect to receive it so quickly. Thank you!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Hillsborough, CA
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken start switch shaft
Removed 2 rear philips sheetmetal screws. Popped lid off w/ flathead screwdriver. Rotated old switch counterclockwise. Moved 2 terminals from old switch to new. Put everything back together in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from lake villa, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer would dry for the first 5 min them make noise with no heat.
my experience was just like the other responses. top comes off, 2 screws and the front comes off and the screws to the solenoids come off. Replaced the solenoids and put everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Bellingham, WA
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken start switch they used pliers and broke the stem
Pulled the unit from the wall, Unpluged the power and removed the back cover behind the switches. twisted the switch removed and removed the wire, inserted switch and turned in place. Put the button on and good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from santa cruz, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heat was intermittent
Unplug dryer.
Put up the top of the dryer at the front, remove 2 screws holding the front of the dryer to the sides and remove front of dryer. Locate ignition coil on lower left. Remove 2 screws and bracket over the two ignition coils. Replace coils and reassemble in reverse.
Everybody's happy.
Put up the top of the dryer at the front, remove 2 screws holding the front of the dryer to the sides and remove front of dryer. Locate ignition coil on lower left. Remove 2 screws and bracket over the two ignition coils. Replace coils and reassemble in reverse.
Everybody's happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi Dixner from Nashville, TN
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
start knob broke off
I removed all but one screw on the back of the control panel and slid the panel down and to the left. Then I jiggled and turned the start switch box out of the slot, unplugged it, plugged in the new switch, and put it back in the slot turning slightly to tighten into place. I replaced the screws and the repair was complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margery from Hartland, ME
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The drum belt was making a squealing noise, and it looked frayed.
After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.
PS this dryer is 23 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHNNY from LONG BEACH, MS
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burner Want Stay Light
Removed burner, unpluged 2 plugs on coils. Removed 2 screws, replaced coils, pluged 2 plugs to coils replaced 2 screws. Reinstaled burner. Dryer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kennedy from Fairhope, AL
- Parts Used:
- 5303307893, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Loud squeaking
Removed drum and replaced drum support bearing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Berkeley, CA
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Loud, piercing screeching from dryer
I followed others instructions on this site to disassemble but felt confident since 2-3 years prior I had replaced the felt top/bottom guides around the drum and the drum belt. The video on this page is also helpful
1) Pop the top with a putty knife
2) Unscrew two screws that hold the front onto the dryer frame
3) Lift front from two clips at bottom of dryer
4) Release tension from belt (unscrew/remove rear access plate)
4) Lift drum up and forward out of dryer
5) Unscrew drum bearing 3x screws from inside of drum
5) Remove the drum bearing holder
6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes.
7) Attach drum bearing
8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup)
9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place
10) Reverse steps to assemble
I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!
Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.
1) Pop the top with a putty knife
2) Unscrew two screws that hold the front onto the dryer frame
3) Lift front from two clips at bottom of dryer
4) Release tension from belt (unscrew/remove rear access plate)
4) Lift drum up and forward out of dryer
5) Unscrew drum bearing 3x screws from inside of drum
5) Remove the drum bearing holder
6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes.
7) Attach drum bearing
8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup)
9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place
10) Reverse steps to assemble
I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!
Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Bells, TN
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Loud squeeling noise
I had trouble with the little piece on the back side of the dryer not lining up with the bearing housing. I also didn't see how the drum was gonna stay in place but finally realized the front cover lines it up. All in all it was awesome to get the part I needed so quickly and cheap, thanks a lot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Loveland, CO
- Parts Used:
- 5303281153, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Bearing Was Very Noisy
Excellent!!! The parts fit perfectly, but most of all was the video that went through the repair step-by-step.
A local repairman quoted $198 for parts and another $150 for labor. Got the parts here for less that $26!!!!
The only issue (very minor) was the video called for a phillips head screwdriver to remove the front panel, and our dryer needed a squarehead driver. (If I was younger, I would have been able to see the problem).
But, I highly recommend Partselect!!!!
A local repairman quoted $198 for parts and another $150 for labor. Got the parts here for less that $26!!!!
The only issue (very minor) was the video called for a phillips head screwdriver to remove the front panel, and our dryer needed a squarehead driver. (If I was younger, I would have been able to see the problem).
But, I highly recommend Partselect!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kurt from Fargo, ND
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Loud sqweeking after dryer was in operation for over an hour
FOLLOW THE VIDEO!! I was scared to even get into it until I watched the video. Made it easy for me and I have little to no mechanicl skill. Excellent video that made it super easy. Took me an hour as I was taking my time. Now I could probably do the same repair in 20 minutes.
Was this instruction helpful to you?
Thank you for voting!