1106307400 Kenmore Dryer - Instructions

After removing the front of the dryer it was evident that the blower boss had broken where the motor shaft comes through and is attached. I removed a few more parts to make the blower more accessible and removed it. I then machined a new boss and attached it to the blower and reinstalled it.I then did a quick continuity check on the three thermostats since the dryer was already apart.I discovered one was faulty and ordered a new one from you.That repair took all of five minutes.The irony of the whole thing is that while I was ordering the thermostat from you,I asked out of curiosity,if the blower was still available. As it turns out it still is but the new machined part worked out great and the dryer was back up and running in no time.

Thanks again,
Dave

I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.

I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. almost spent $400.00 on a new one.

This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

For 2 years, I propped a broom stick against my dryer door to keep it shut while it was running. Last Sunday night, I decided that it was about time to fix it. I found the PartSelect site, which was extremely easy to navigate, and ordered a replacement kit. It arrived in 2 days via Fed Ex and actually contained extras of each of the 2 components, in slightly different sizes. It took me about 10 minutes of eyeballing the parts to figure out how to place them and about 30 seconds to install the new latch parts. They fit perfectly. Great site, great service, I would highly recommend this site.

Took the back off the dryer. Disconnected the old thermostat and installed the new thermostat. Connected the back of dryer. Put in a load of clothes to dry and the clothes were dry on the first try. Works like a new dryer. Saved a lot of money not having to buy a new dryer when all I had to do was replace some old parts.

I didn't have to remove the entire door...I just removed the screws with the door open, used a needle nose plier to remove the plastic insert..stuck the new one in. Then I replaced the metal portion by popping it out and inserting the new one. Easy

This dryer refuses to die and I am happy to keep it that way. Door latch was replaced in less than a minute using this kit. Easiest repair ever.

Got online with parts select, easily found the parts needed and ordered them. They arrived very quickly. The repair itself took all of 5 minutes and now the dryer door stays shut like it is supposed to. Only complaint is shipping was more than the parts but then again, I didn't waste a lot of time running all over town looking for what I needed. So, in the long run I saved money , especially when compared to a calling someone else to fix it.(big bucks for even the most minor service call as you all know).

pop off put in done

following the repair video made it super easy. thanks!

Order one new latch, receive 2 spares. Pushed new latch in, re oriented the catch. was done in less than 5 min

I got my kit and when I opened it the exact parts were there!! I am a older woman and was a little worried that I could do it. I took the pliers and pulled the old latch catch out and 1-2-3 walah!! It was so unbelievably easy. If I can do it anyone can. Thank you for saving me hundreds of $s on a new dryer.

Just pulled the old parts out on door latch and put the new ones in. Thanks Parts Select for your prompt response and easy process for order and shipment.

Repair was very easy simply used a screwdriver to remove the cracked old latch and used my fingers to insert my new latch.