11060904990 Kenmore Dryer - Instructions

Just replaced part

i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on

I took the timer knob off, then took the back off. I then took a picture of the so I would know how the wires would go back but I didn't need because the timer is labeled. I then took the timer out snapped wires off then replaced them on the new one and bolted it back it. It was very easy and took less than 15 min to do.

Cut power at breaker panel to Dryer.
Remove back cover of controls panel by removing six screws. Removed control knob and one screw from timer. Removed wires from bad timer (one at a time) and put them on new timer. Installed new timer in control panel and replaced the knob and screw on front. Then replaced panel on back of control panel. Cut power back on at breaker panel and tested unit for proper operation.

Two screws hold the top control panel in place. Once removed the panel could be tipped forward. The Push to Start switch had 2 wires which were removed and swapped to the new starter switch. The old one rotated 90 degrees to remove and the new one installed. Panel was resecured to the top of the dryer and tested. Worked first time. Finding the part on the website, ordering it, receiving it quickly and the install couldn't have been easier or more pleasant or efficient.

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

After replacing many, many parts the dryer still does not work! Replaced Thermo Fuse, Thermostate, Cycling Thermostat, Coils, Ingition Sensor and Ignitor. Ran meters across all incoming power, timer control, ignitor power, etc. all check out according to schematic. Incoming gas supply is functioning. So, 6 parts recommended later still same problem. On the good side, all parts were shipped out very quickly. Highly impressed with service.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal Fuse blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.

Opened access door, noticed main power wire to heating element was partially melted. This was caused by a bad connection to the drying element, loose. Removed heating element assembly. Cut bad section of wire and added new connection. While doing this the thermostats plastic casing cap came off ! Probably due to exessive heat / resistance from the bad connection. This confirmed why there was no heat. Intalled new thermostat and and am now good to go !

After receiving the part I unplugged the dryer and took the back cover off of the controls on top off the driver with a Phillips screw driver and visually confirmed that the new switch matched. Removed the wires one at a time from the Push to start switch and connected them to the new one as I removed them. I then plugged the dryer back in and tested that the new switch would fix the problem. Once I knew the new switch was the I uninstalled the bad switch and installed the new switch in to the control face. Put the cover back on and slide the dryer back in to place.

It's a electric dryer, I knew it was related with the thermal !

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Took, back cover out,but first i disconect the electricity,i give a fast look,looking for anything wrong and i saw a thermostar burn out in the element case,the bottom one,a thermostart
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.