1106957703 Kenmore Dryer - Instructions

Removed top, then remove front panel, then removed the drum, and the idler pulley assembly. Then added new parts, and reversed procedure to assemble back to new.actually runs better, now. Dryer is approximately 30 years old.

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

watched your video on 'how to' and did it like man showed..no problem

Disassembled dryer, removed tumbler, replaced drum support rollers

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly

Recommend 10" or larger 14" will definitely do the job

2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatural

3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example

Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

removed the top of the dryer exposing the drum and belt.Also the bottom acess door was removed.The rollers were easy to get to from the bottom and from the back.Had to remove ducting from the rear of the dryer to expose the upper most roller shaft nut.Loosened the nuts from the back making the wheels come from the bottom.Also had to loosen the support bracket holding the weight up on the bottom roller assy.Replaced the belt by rapping it around the drum before installing the roller wheels.This project was easy except trying to hold the upper shaft in place while putting the nut back on the shaft.This would be much easier with a second person.Thanks for making this a nice experience and easy fix !

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

Followed the instructions and the repair went like clockwork, took less than an hour. I spent more time brushing and vacuuming old lint from the innards of the machine than I did doing the actual repair. Finished up $0.78 richer, too, from the change I found inside the machine.

Was a little hard getting at the idler pulley being it was behind the blower assembly, but it was the only draw back.