Models > 11076408650 > Instructions

11076408650 Kenmore Dryer - Instructions

Jump to:

All Instructions for the 11076408650
121 - 135 of 1361
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dan from SYRACUSE, UT
Parts Used:
279827
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Mother was frozen up
I followed the video. So easy..
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lance from RCH CUCAMONGA, CA
Parts Used:
WP3392519
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set
My dryer would not heat. Drum was spinning fine and everything else was working just no heat.
I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tommy from BRUSH, CO
Parts Used:
341241, 279827
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
dryer motor quit working
i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from JOLIET, IL
Parts Used:
349241T
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Rear drum rollers were shot.
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Craig from VASS, NC
Parts Used:
WPW10359270, 349241T
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
The drum made a lot of noise while turning. The dryer shook
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from N. Ferrisburg, VT
Parts Used:
W11613302
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Gasket was falling off, needed replacement
Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Miriam from BRUNSWICK, OH
Parts Used:
339392
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Broken lint filter
Opened new package took item out and put it on the slot where the old filter was. Easy as pie. My dryer is 46 years old and works just fine.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
steven from Buffalo, NY
Parts Used:
339392
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Original lint filter had broken handle
Ordered a correct part # lint filter from this site, removed old filter & installed the new, very simple fix.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Manny from ODESSA, TX
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Dryer would not start!
Unplug unit first.
Took the front cover off the front of dryer below the door.
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
james from york, PA
Parts Used:
W10820036
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Dryer would not run
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MONA from SHAMROCK, TX
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Dryer would not start.
I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from MACON, GA
Parts Used:
W11415783, WP339956, 279505
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins
chute wore out
I never received my part checked back after said hearing part had been shipped was told part was no longer available have called twice about my refund and not received that either
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ronald r from gainesville, FL
Parts Used:
WP691366, 349241T, 341241
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Noisy thumping dryer
Followed the instruction given by previous writers in these post.
Hint The bungee cord hook was used to hold up the lid, worked very well.
If you are by yourself use duct tape to hold the drum in place before removing the front panel. Tape the top rear of the drum to the rear frame. Also do this when reassembling the front panel.
Easy and quick makes the wife happy this time.
PS. Ordered the parts on Sunday and had them on Tuesday.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rodney from Mt. Jackson, VA
Parts Used:
349241T
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
the lower drum support roller had been chewed to bits.
I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
peter from portland, OR
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Broken belt
Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11076408650
121 - 135 of 1361