11062872102 Kenmore Dryer - Instructions

Followed the PartSelect instruction video.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.

Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.

The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.

Troubleshhot problem, used multimeter to verify current to motor. Once that i was sure motor was getting proper voltage, I used a meg-ohm meter on A/C motor windings and physically tried to turn motor and found that it was siezed. I then cleaned inside of unit inspected belt and drum rollors. Due to the cost of the items, I decided If I was going to replace the motor I should replace all moving parts, and install new belt. Everything went easy. WHAT WAS MOST IMPRESSIVE! was that the Parts people sent the correct parts on time the first time, with no hiddin charges. There web site should accurate diagrams of parts and internals of machine. I was really pleased and will use this service again. Thank you

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.

Boyfriend stated it was simple, he removed the back and replaced the part using a few everyday tools.

My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 business days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the company was a perfect fit.

Unplug Dryer.
Disconnect dryer vent line from rear of machine.
Removed 8 screws holding back cover on.
Removed back cover.
Disconnect 2 quick connect wires from dryer heating element tube on right side of the machine.
Remove 2 screws holding element cover in place.
Remove cover and element.
Remove thermostat from unit and connect to new unit.
Re install parts in reverse order of above.

repair was fairly cut and dry...if you have any handyman experience....the hard part was partselect web page...starts out easy to locate part if you have the correct model number....however after that it can be confusing as to what you are looking for part wise and if you have located the correct part....diagrams are helpful if you could see them and/or understand them or what you are looking for....as a novice can be fustrateing....even after calling partselect for help/explaination....other wise it went well for a repair and hopeful will get another 10yrs out of this dryer.....

1 screw to replace.

Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519

Followed instructions from video, just removed lint collector, dryer top and front panel, removed broken belt and old idler pulley. Vacuumed and cleaned up inside dryer.installed new pulley and rib belt according to printed instructions,installed new dryer duct and new clamps. Saved myself huge service call or having to buy new dryer.Will be checking with this site on any future repairs instead of calling a repair service. Your video made it real easy to repair.and I am 77 years old.. Bob

Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up. Replaced front and top.

Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.