1106618800 Kenmore Dryer - Instructions

Replaced the cap over the door switch so when the door closed the switch was engaged

Unpluged power cord.removed top and front pannels(after disconnecting wiring to door switch.) Removed drive belt to drum,and removed drum. Checked and marked motor wiring before disconecting from motor.Removed motor,After unscrewing the blower from shaft.(Had to remove jumper wire from motor)Reinstalled the blower and secured the motor,reconect wires to motor.(rechecked wiring connections)Put back the drum,drive belt,and the front door pannel.(reconect door switch wiring)then the top pannel.Plug in the power cord and checked opertion.....WORK'S JUST FINE! I ordered the replacement motor on a sunday,and the new motor was setting on my kitchen table tueday afternoon when i got home. Great job" PARTSELECT."

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

Was informed that I had a bad dryer motor and no warranty. Unplugged the unit. Removed to screws in the lint trap slot. Used a small blade screw driver to pop the 2 clips at the front of the dryer top. Lifted the top and rested it up against the wall. Removed 2 screws holding the machine front panel. Removed the front panel and removed the tub. Couldn't get the blower loose from the dryer motor so I cut it off with a hacksaw. Moral if you are going to replace the motor go ahead and by the blower too. It is less than $20.00. Popped 2 clamps loose holding the motor in and removed it. Placed the new motor in the unit. Strapped it down and attached the new blower. Plugged it in, put the dryer back togehter and tried it. It worked.

Repair was simple, minus pulling the drive motor shaft out of the back fan. The female end of the dryer fan was made of plastic, so the socket wrench cracked the plastic end. Other than that, the repair was simple and easy to do. Much better paying the $88 for a new motor vice paying $400 or more for a new dryer. Dryer has run like a champ since replacing.

Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!

I googled the problem, then came across a site where somebody had experienced the same problem, and they changed the door catches to resolve it. I did a search for Whirlpool parts and found "partselect.com". I followed the instructions on the website and located the parts very easily and also discovered that there was a video on how to make this repair. We were tolerating this problem for quite some time and now the problem is resolved, thank you...

I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

removed the broken part and replaced with the new one

This was a classic easy repair and I am sure saved us bundles on a service call.

very easy

Screwed in light bulb and glass protector

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.