11086294500 Kenmore Dryer - Instructions

Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.

I followed the video. So easy..

nobody has said it yet so... to take a dryer apart, take the back off, pull the lint trap, remove two screws on back of the top piece. the whole top shifts forward and disengages two clips on front corners, it then tilts up and back. the front comes off next, this frees up the tub. all parts ordered replaced worn parts, though there was no smoking gun as to the source of the sound. once it was apart, it was a cakewalk. had it up and running in 45 minutes. can't see how it took others two hours.

The first step was to check the electrical supply to make sure I had power 120 volt. I unplugged the dryer and turned off the gas supply and turned the dryer around so I could have access to the back panel removed panel to access the wiring harness and safety thermostats. All switches and wire checked good with my ohmmeter .I pulled off the front kick panel and checked the electrical schematic and found the door switch was in the circuit to check it I had to lift up the top and pop out the front to access the door switch checked switch and found it defective. Replaced switch vacuumed out dryer and vent reassembled dryer and all worked good.

Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.

I replaced the front seal and bearing, split ring bearing and rear seal. It was technically pretty easy. The thing to do is watch the videos provided by PartsSelect AND go to Youtube and watch a couple of others. Once you see several guys do the job and look over your own machine, it all becomes obvious. Some tips: Work cleanly, you will be dealing with dryer dust and shredded gasket material. Use a vacuum and put down newspaper or a drop cloth. While you have it apart, clean the inside of the machine, and check the other moving parts (eg, rear bearing and drive belt). The glue for the rear drum seal is runny and dries fast so work reasonably quickly. I held the seal on with clothes pins and binder clips and glued about a foot of seal at a time. Everything else goes on easily. They dryer is like a new machine-good for another 30 years.

I unplugged the dryer from the electrical outlet, removed the back of the unit and checked the heating element for continuity. There was no reading. I then removed the housing and heating element and visually inspected it. The coiled wire was broken in two places.
I then did a Google search with the model number and found Parts Select. I placed my order Sunday afternoon and the part arrived the following Wednesday. That evening it took about 20 minutes to install the new element,put the back on the dryer and re-attach the exhaust tube.
The old dryer is as good as new again.
TJ in Boise

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

10 min. job, easy to do / two screws top and two inside front / remove old parts install new.

turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Fit great,well please with order!

Step 1: Unplug the unit, then remove the lint screen and then remove the two screws beneath the lint screen cover. Step 2: At the rear of the dryer there is a small protective metal panel near the upper part of the dryer - remove this first; then at the front of the unit, insert a plastic pry tool between the front edge of the top and the front panel of the dryer and gently pry the top loose. Step 3: Lift the dryer top up and either remove it entirely or let it rest on the back edge and a wall for support. Step 4: On the inside of each side panel near the top front, locate the two screws holding the sides of the dryer to the front panel and remove them. Step 5: Carefully slide the front panel up so that the panel detaches from two metal clips holding the front panel onto the side panels. The drum will likely drop down slightly at this point since it is no longer being supported at the front. Step 6: On the front panel there is a wire that connects the front panel door switch. I left that intact because it was too difficult to remove without risk of breaking it and instead simply set the front panel to the side of the dryer - but if possible remove disconnect the wire and then set the front panel aside. Step 7: Remove the drum by pulling it out, inspect the back felt seal for wear and also the plastic split ring bearings at the front end. When you remove the drum belt the tensioner pulley underneath the drum will likely fall over, but this is to be expected because without the belt and drum providing tension, the piece only fits loosely in a slot at the bottom of the dryer. Step 8: Inspect the drum rollers, motor, and other parts for wear, then vacuum out the inevitable lint and dust inside the unit. Step 9: At this point I also decided to inspect and clean out the lint chute at the back of the unit, so I removed the protective back cover and removed the screws holding the lint chute in place. I then cleaned out the lint that builds up over time inside the chute and checked the two foam lint chute seals at the back of the unit - these needed replacing so I removed the old deteriorated foam and vacuumed off the back of the unit and then adhered the new seals to the back of the dryer. Step 10: Take the new multi-rib belt and drape it around the drum with the ribbed side against the drum - you will likely see a mark around the drum where the old belt was positioned, so use that as a guide. Step 11: Since one of the split ring bearings on my unit was worn, I replaced both at this time by simply pressing the plastic tabs out of the slots at the front of the drum, removed each half of the ring, and reinstalled the new parts - they only correctly fit one way so that the plastic edge lines up cleanly with the front edge of the drum. Step 12: With the felt drum seal toward the back replace the drum - I used a small box to support the drum upon while I reinstalled the drum - this will make it much easier to manipulate the belt around the tensioner and motor. At this point I reached underneath the drum and reinstalled the tensioner. by positioning it in the two small slots near at the bottom panel that are near the front of the dryer motor. Then take the belt and pull it through the tensioner and around the motor pulley at the front of the unit. You will likely have to push up slightly on the drum and tensioner to allow the belt to be pulled through the tensioner and around the motor pulley. Step 13: Rotate the drum slowly by hand at least one full revolution and check to see that the felt seal at the back is not pinched and that the belt does not fall off the pulley. Step 14: I removed the box supporting the bottom of the drum, then took the front panel and fit the front of the drum against it so that the split ring bearing matched up to the front panel. Step 15: The drum will still be somewhat loose and that allowed me to carefully lift the front panel up and then slide it down back onto the two metal clips that hold the front panel to the side panels. Step 16: Reinstall the two screws that also hold the front panel to the side panels. And if you also removed the wire connection to the dryer door, reattach that too. Step 17: If you removed the lint chute, reinstall it from the back while the lid is still off so that it is easier to slide it into position. Step 18: Reattach the top of the unit by seating it against the top of the frame (of course if you disconnected wires, reattach those too) and reinstalling the two screws underneath the lint screen cover. Step 19: Reattach the rear panel cover and small protective metal panel. Step 20: Reattach the flex-hose to the lint exhaust.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

Ordered the motor with pulley and blower wheel in case the wheel did not come free from the motor.
Took out the lint screen, took off the top and disconnected the wires for the door switch, took off the front.
Remove the idler poi and the belt and then removed the drum.
I read in other repair YouTube videos, the blower wheel sometimes is so seized onto the motor axle that you have to remove the wheel by cutting it off.
Yes, ours seized!
Cut off the motor axle with a hacksaw and then the motor and the wheel were free. This was not an issue since I had purchased both the motor and the wheel which I recommend doing anyway. Our dryer over 25 years old and it does not have many electrical components, which I love. We removed the parts put in the new parts. Follow the wiring diagram to get the new motor hooked up.
Then I replaced the drum support rollers, which were a snap and then we put it all back together.
We added an extra step because we had to takeoff the back of the dryer to gain access to the blower. It turned out to be a good thing since years of lint have been trapped at the bottom of the lint chute.
I cleaned everything, washed everything and put it all back together and it purrs like a kitten.
Took us about 2 1/2 hours total since we are very cautious and slow as we didn’t want to break things.
I am very happy with the end result and hopefully it will last another 25 years!
Parts were spot on and worked perfectly.
Much more economical than buying a new dryer for $750-$1000.