11097284110 Kenmore Dryer - Instructions

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.

Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.

I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked up the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.

all that was required was to push the catch into the slot notools needed.

You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...

Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place located just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.

Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way. The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.