41769052990 Kenmore Dryer - Instructions

Took out of package. Used screw driver to pop off old broken handle.
Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.

Took the front off the dryer and removed the old switch and put in the new one.

I YouTube'd how to repair it. It was super easy. Needed a power drill to get the screwsa off and a flat head screwdriver to pry off the wires but besides that it took about ten minutes and I was finished.

popped in one in

Taking apart the dryer was easy. Pop the top, take out two screws, separate the front panel from the drum. Removed the old felt seals but much remained. Used a wire wheel on my drill to clean off felt and old glue (most difficult part). Applied new glue,used a band clamp, one hour later I reassembled the dryer; works fine. No more burn marks on clothes!

UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.

disconnected power unlocked both top sides ,lift top back and take top 2 screws out, then unhooked wiring,then remove whole front away from drum.scrap off all the remaining pieces, then glue and wait till tacky, then apply
front lower basket seal and top drum glide seal,replace the front ,hook wires back to proper place , put the two top screw back on!!! happy drying!!!

Followed the video

replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.

there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!

I cut off the four that didn't line up - I suppose since this was a gasket that fit several makes, I should expect this type of problem.

removed old seal and drum glide. sanded off old glue. replaced with new parts, cleaned out the whole bottom of the dryer, runs good as new.

First I took the drum out of the dryer. This was an easy tear down. I had to remember 2 wires, and a belt assembly ( 2 pullies ). I removed 3 screws inside the drum to release the bearing assembly from the back. Then I went to the dryer chasis and removed the mounting bracket by removing 2 screws. I simply replaced the mounting bracket with the new one. This required having to use a magnet to hold a small ball bearing in place while I worked the rest of the pieces in position.I greased it up and went back to the drum. I replaced the old bearing assembly with the new one. Easy. I took the time to shop-vac the inside of the dryer. There was a lot of loose lint, candy rappers, coins, etc. Finally, I put it back together. Unfortunately, this is the forth (4th) time I've had to do this. It's cheaper than buying a new dryer. Now, I've got to fix the washer.

I first looked at your directions then felt I could do the repair. So I ordered the part. The video was extremely helpful and allowed me to follow each step in the process. Last time I paid $270 for the exact repair. This time I costs me under $30. Plus I was able to clean out the entire inside of the dryer. The sitr instructions were very helpful and on target for any level of experience. I fixed my own dryer and saved a ton on it! Thank You, Randy In Colorado

First I unplugged the dryer. Then I gently pryed the top of the dryer. This was done from the front using a flat screw driver. Do this gently pushing up on the handle of the tool. It will pop up one side at a time. No need to remove the screws and clips on the the rear top of the dryer. Set the top aside. Then from the inside front of the dryer using a phillips screw driver I removed two screws, one on each side. This allowed me to lift the front of the dryer up and away from the unit, off the two clips on the bottom front of the unit. I set the front cover on top of the dryer. There is no need to disconnect any wires. Next removed the rear vented cover on the back of the dryer so I could acess the belt pullies. From here I pushed the upper left pully to the right to ease belt tension and take the belt off that pully. Slide the belt to the rear of the drum. Next I removed the three screws from the center most part of the inside of the dryer drum. My dryer required the use of a square head driver tool. This allowed me to easily bring the dryer drum out the front of the unit. Set it out of your way. Then I vacuumed the dust out of the dryer. Then I lifted out the metal part that resembles a trailer hitch which had been attached to the dryer drum. Next using a nut driver I removed the two screws which hold the white plastic part of the bearing assembly to the rear of the dryer. That is all the taking apart work.
Putting it all back together was not too difficult. First install the new white plastic part of the bearing assmbly inside the dryer along with the metal part on the outside rear. The little metal ball bearing goes on the OUTSIDE between the little metal part and the rear wall of the dryer. Do not leave it out as it provides electrical grounding between the dryer drum and the body of the dryer. Next attach the new bearing part that looks like a trailer hitch to the rear of the dryer drum. This is the three screw part. Then lift the drum back into the dryer. Do not yet set the drum all the way in. The dryer belt must be looped around the drum. I installed a new belt. If the bearing is worn out it is time for a new belt. The smooth side of the belt goes against the dryer drum. Now apply a generous amout of lubricant to the white plastic cradle which was installed on the back of the dryer and to the ball bearing area. Then the dryer drum may be set into place, that is the trailer hitch part into the white plastic cradle. Now the front of the dryer may be reinstalled. Push up on the inside of the dryer drum to line everything back up. Put the two screws back which hold the dryer front on. Be carefull not to drop them inside. Put the dryer belt back into place on its pullies. It goes on the inside of the left and right pullies and on the outside (bottom) of the pully of the dryer motor. Check for and undo any twists. Plug in and test the dryer. All should be well. Reinstall the rear vented cover. Replace the top, connecting the rear first. Make sure to reattach the green grounding wire. Then push the front of the top down onto its clips. You are done! This took me 1 hour and 10 minutes. It sounds like alot but you can do it! Empower yourself!