1106108710 Kenmore Dryer - Instructions

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!

Replaced the cap over the door switch so when the door closed the switch was engaged

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

This was a classic easy repair and I am sure saved us bundles on a service call.

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.

Repair was straight forward with only two screws to undo. Popped the two sides in and I was done. What was amazing was the lowest cost on parts and the timely delivery.

Screwed in light bulb and glass protector

very easy

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!

The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!

The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen the two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.