1106618801 Kenmore Dryer - Instructions

First I removed the rear panel of the control sectio and the main rear panel. I checked the switches and fuses. The fuse for the dryer vent was giving an intermittent signal, so I replaced it with one I picked up at a local repair shop.
Since I had started working on it, and due to the age, I went ahead and ordered a motor, belt, and drum rollers and replaced these as preventive maintenance.
Once you realize how everything comes apart, it is not a very dificult job to overhaul the complete dryer.

Replaced the cap over the door switch so when the door closed the switch was engaged

Unpluged power cord.removed top and front pannels(after disconnecting wiring to door switch.) Removed drive belt to drum,and removed drum. Checked and marked motor wiring before disconecting from motor.Removed motor,After unscrewing the blower from shaft.(Had to remove jumper wire from motor)Reinstalled the blower and secured the motor,reconect wires to motor.(rechecked wiring connections)Put back the drum,drive belt,and the front door pannel.(reconect door switch wiring)then the top pannel.Plug in the power cord and checked opertion.....WORK'S JUST FINE! I ordered the replacement motor on a sunday,and the new motor was setting on my kitchen table tueday afternoon when i got home. Great job" PARTSELECT."

i did not do the repair but when my friend finish it was great, this company is great.

Read earlier posts on the change out of motor with times varying from 30min to days. My ordeal was in the days category. Long story short, I could not get the blower off. The back of the blower has flats to use a adjustable wrench and you can use a socket on the back of the motor. I rounded off the flats on the blower and had to cut it off. Since I had only ordered the motor, I had to then order blower. If you can get the blower off the motor is about a 30min to 1 hr job. I would suggest purchasing the blower along with the motor to save some time.

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

very easy

Screwed in light bulb and glass protector

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

This was a classic easy repair and I am sure saved us bundles on a service call.

I googled the problem, then came across a site where somebody had experienced the same problem, and they changed the door catches to resolve it. I did a search for Whirlpool parts and found "partselect.com". I followed the instructions on the website and located the parts very easily and also discovered that there was a video on how to make this repair. We were tolerating this problem for quite some time and now the problem is resolved, thank you...

Repair was simple, minus pulling the drive motor shaft out of the back fan. The female end of the dryer fan was made of plastic, so the socket wrench cracked the plastic end. Other than that, the repair was simple and easy to do. Much better paying the $88 for a new motor vice paying $400 or more for a new dryer. Dryer has run like a champ since replacing.