41780052990 Kenmore Dryer - Instructions

OK, this is a follow-on repair story.. I *did not* order the lower basket seal when I ordered the upper basket seal... shame!!! BUT, I am now exceptionally quick at removing the front panel - less than 20 seconds!!!

For those who are considering doing this repair, there are more detailed explanations below - my only tip to help do this "quickly" would be to get some automotive brake cleaner to dissolve the old adhesive .. it is AMAZINGLY effective.. The best part is, don't worry about completely removing the old felt when you are tearing it off.. If some is still stuck to the door, it will actually hold some of the brake cleaner in contact with the old adhesive, which accelerates dissolving of the adhesive. Scrape it all off with a plastic scraper, and wipe it down a few times - surface is prepped & ready for the new adhesive + basket seal.. Use spring loaded clamps to hold the seal in place as you install it also.

I First pulled the top panel up and off from the front. Then, on the inside, removed a square head screw from each side holding the front door panel on. I then pulled off the front panel enough to expose the drum. I then removed the old drum glide with a putty knife, and following instructions supplied with the new glide, glued the new glide into place. I then assembled in reverse order of disassembly.

Open the top cover by pushing the retention clips in from the front (just under the top edge) with the putty knife - that was the hardest to figure out - I found it online.
The rest is just 4 screws - 2 inside to release the plastic filter holder and two on the inner edges of the front panel.
Took the front off, ripped the old slider, cleaned the glue residue with alcohol and mineral spirits and a lot of scrubbing, vacuumed all the lint from the fan.
Then glued the new slider in place and clamped it together. Didnt know how long the glue takes so I left it overnight, just in case.
It works well now. Cleaning the ducts and the fan with the vacuum hose made a world of an efficiency difference. They should make an easy way to do this for regular maintenance!

First I removed power from dryer. Then I lifted the lid and removed the 2 screws holding the front onto the dryer. I then used a pair of pliers to grip the seal and help pull it off. Cleaned off old adhesive. Recommend getting GOOP BE GONE. Then apply high temp sealant onto area and place seal on top. Press firmly across it to make sure it is in place. Then put it all back together and your done. Also, if upper seal is worn.recommend ordering lower seal at same time. I didn't and should have. Save yourself from doing this twice.

I cut off the four that didn't line up - I suppose since this was a gasket that fit several makes, I should expect this type of problem.

replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.

Remove top cover and front and remove drum and install a new bearing kit and new belt.

Removed the door and replace the upper glide and the lower seal. The repair was easy.

Followed the video

As all others have said, without being redundant, I'd view post #1 or #2 for a good detailed set of instructions.

The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I could see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.

Once I figured that part out, it was a piece of cake.

Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

Watched on-line video, then applied those steps.
1. Pop the front of the deck loose using putty knife to depress clips;
2. Disconnect wires from light and door switch;
(Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.)
3. Remove lint filter mount screws and mount from bottom of door opening;
4. Cut drum belt with wire-cutters and removed it;
5. Remove drum support clip from top center of front panel;
6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel;
7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front;
[While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.]
8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.);
9. Have a second person hold the new ball hitch in position while starting screws, if necessary;
10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip;
11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel;
12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver;
13. Start drum belt on motor shaft and position against tensioner pulley;
14. Feed drum through front of machine and loop belt over rear of drum;
15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley;
16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing;
17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.

I first looked at your directions then felt I could do the repair. So I ordered the part. The video was extremely helpful and allowed me to follow each step in the process. Last time I paid $270 for the exact repair. This time I costs me under $30. Plus I was able to clean out the entire inside of the dryer. The sitr instructions were very helpful and on target for any level of experience. I fixed my own dryer and saved a ton on it! Thank You, Randy In Colorado

Just like in the video, but with a stackable washer/dryer unit, works like new now....