1106717502 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Billy from NEW BERN, NC
- Parts Used:
- W10820036
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would not start, timer had no power to it.
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- satyavenkata from Bentonville, AR
- Parts Used:
- W10820036
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
The switch was not working so got a new switch
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Marion, KY
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Noise in dryer when dryer was turned on
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,
Your great service is very hard to find.
Your great service is very hard to find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ava from BALTIMORE, MD
- Parts Used:
- 349241T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer making excessive noise; then continued to blow circuit
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from EVEREST, KS
- Parts Used:
- 349241T
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
rollers had been new too long!
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Perris, CA
- Parts Used:
- WP230131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The door cables broke.
I replaced the springs and cables in the dryer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LINCOLN, NE
- Parts Used:
- WP238460
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Stepdaughter had over the years broke the 2 cables that supported the drop down door. So she let it hang by the hinges, which eventually broke them also.
Removed what was left of the old hinges, installed the new ones. Also added a length of jack chain (same size chain that’s on a toilet flapper) to one side to support the door while open. Tried to chain up both sides but it wouldn’t let the door completely close and depress the switch. Cables are no longer supplied by any parts dealers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from OAKLAND, TN
- Parts Used:
- 279771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dryer would not heat and the timer would not turn as it should
I replaced a bad thermostat
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from COAL CITY, IL
- Parts Used:
- 239087
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum rear seal bad
Took off old one clean surface up then put glue all around drum seal area wait one min. Or tacky then put seal on reassemble the drum. Works good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Rupert, ID
- Parts Used:
- W11415783
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was not drying clothes with-in 40 minutes. Found lint guard was not sealed properly at base, exhaust hose full of lint.
This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the discharges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!
Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SANDWICH, IL
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Would not drain
Replaced lid switch, but problem still continued.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melody from TEXARKANA, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer door wouldn't catch and stay shut
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from KILLEEN, TX
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
door would stay closed
just replaced parys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Newport, VT
- Parts Used:
- WP691366
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken belt
removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from MOUNT VERNON, IL
- Parts Used:
- 339392V
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
filter had holes
pulled old filter out and then slid the new filter in Done
Was this instruction helpful to you?
Thank you for voting!