1106607410 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Laszlo from Vienna, VA
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door switch actuator spring broke
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from MOUNT VERNON, IL
- Parts Used:
- 339392V
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
filter had holes
pulled old filter out and then slid the new filter in Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from NORFOLK, VA
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Won't pump out the water
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from Buffalo, NY
- Parts Used:
- 339392V
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original lint filter had broken handle
Ordered a correct part # lint filter from this site, removed old filter & installed the new, very simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from UPPR MARLBORO, MD
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken dryer door catch
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from ENDICOTT, NY
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from HUDSON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
I followed your short video and found it very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from PLAINFIELD, IL
- Parts Used:
- WP691366
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dryer drum wasn't turning
Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from el paso, TX
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Broken door switch
I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Perris, CA
- Parts Used:
- WP230131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The door cables broke.
I replaced the springs and cables in the dryer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from NEW BERN, NC
- Parts Used:
- W10820036
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would not start, timer had no power to it.
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from New Richmond, WI
- Parts Used:
- WP691581
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Light stayed on, inside dryer. Dryer no workie
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LINCOLN, NE
- Parts Used:
- WP238460
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Stepdaughter had over the years broke the 2 cables that supported the drop down door. So she let it hang by the hinges, which eventually broke them also.
Removed what was left of the old hinges, installed the new ones. Also added a length of jack chain (same size chain that’s on a toilet flapper) to one side to support the door while open. Tried to chain up both sides but it wouldn’t let the door completely close and depress the switch. Cables are no longer supplied by any parts dealers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BLOOMFIELD, CT
- Parts Used:
- WP694674
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.
Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SANDWICH, IL
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Would not drain
Replaced lid switch, but problem still continued.
Was this instruction helpful to you?
Thank you for voting!