1106718504 Kenmore Dryer - Instructions

i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

I followed the video. So easy..

First off, start by turning of the breaker to the dryer and confirming the power has been turned off. Next, remove the lint screen and two screws holding the lint screen housing to the lid. Remove the two side moldings on the control panel and the two screws holding doun the enclosure. Slide the control enclosure forward and lift up . Take a picture of the wiring for later reference and carefully unplug the wires and set the enclosure aside. Next, remove the two screws holding the rear lid retaining clips. Gently pry up on the front of the lid to realese hold doun clips, swing the lid up and remove it from the rear clips, set the lid aside. Remove the two screws on corners of front cover located near the top, unplug the door switch. Remove the front cover by lifting straight up, set aside. Now remove the belt from the motor by realeasing the tensioner and remove it from the drum. You can now remove the drum through the front. Now is a good time to check the condition of your drum rollers, clean them as needed or replace them. Clean the roller shafts and apply a quality grease. "Clean the roller groove on the drum" this is what makes the drum sound bumpy! Remove the rear seal and replace it as per the instructions that come with the seal. The glue dries quickly, so have the seal fully in place and apply glue to small areas replacing the seal fully before moving on. You can now reinstall the drum being careful not to damage the seal. Place the drum on the rollers, reach inside and work the seal into place. You can now replace the belt and work in reverse with the casings! It took me longer to type these instructions than it did to make this repair! Enjoy your like new machine!

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

Pull out the old lint filter unit; push in the new one.

Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Ordered a correct part # lint filter from this site, removed old filter & installed the new, very simple fix.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Opened new package took item out and put it on the slot where the old filter was. Easy as pie. My dryer is 46 years old and works just fine.

Removed back and then removed lint slide.
Vacuumed all of the cabinet and and washed lint chute.
Blower seal and lint seals were crumbling since dryer is 24
years old. Part Select diagrams and repair videos are extremely helpful in showing the process. Dryer now working like new.

Followed the video instructions to replace motor, belt, and rollers (belt and rollers looked to be in ok shape, but as long as I had the thing open I figured I might as well). Fairly straightforward procedure. Trickiest parts were getting the rear roller clips in place and re-attaching the rear motor spring clip. Probably could've found a used dryer of comparable quality for less, but this was easier and more satisfying than moving dryers in and out of the basement.

I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.

Followed the instruction given by previous writers in these post.
Hint The bungee cord hook was used to hold up the lid, worked very well.
If you are by yourself use duct tape to hold the drum in place before removing the front panel. Tape the top rear of the drum to the rear frame. Also do this when reassembling the front panel.
Easy and quick makes the wife happy this time.
PS. Ordered the parts on Sunday and had them on Tuesday.