1106308742 Kenmore Dryer - Instructions

Removed old catch and strike with screwdriver and needle nose pliers. Installed new parts. My old catch did not have comparible numbers so I just used the yellow one. Worked fine.

Simply installed the piece and I was done. Took 10 seconds.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

I removed the back before I relized that the motor was under the drum. I removed the front and the drum and accessed the motor. I used a small flat head screw driver to prythe brackets that held th motor in place. I had a bit of a problem removing the motor from the fan. Then I read the web site and figured out that the treading was a LEFT thread. Still had some problems and ended up removing the pully wheel and using a pipe wrench to get the fan off the motor.

I wish I had taken a picture of the pully and belt to see how it went back together, but it went back easy enough.

Very pleased with my effort and guess I saved about $300 bucks on the repair, and the 2 plus weeks to get the guy to my house.

Removed and replaced motor. In the process of removing old motor, the blower wheel had to be unscrewed from the rear shaft of the motor, in order to remove the motor. In my case, the blower wheel had seized up on the rear shaft and could not be unscrewed. It had to be cut off and it also had to be replaced. The dryer now works fine. Tip: I watched an internet video (repairclinic.com)about the procedure before I started. Very helpful!

the plastic fan can be tricky to get off,hold the pully side of motor with an adjustable wrench and turn plastic nut on fan clockwise.mine busted and i had to order another fan but they are easy to put on. counter clockwise to put back on.(reverse treads)

My dryer is probably more than 20 years old. I know, I know, but I decided to fix it anyway. I followed the same steps as the other posters here. However, I almost never fix anything like this and the dryer is in a small space with only a couple of inches of clearance on either side.
The repair took 10 hours off and on over 2 days. You will definitely need another set of hands at various times like when you are unscrewing the fan from the motor shaft and when you are reinstalling the drum and belt.
Getting the motor mount clips off the frame was a huge pain and getting the motor back in place and the clips on correctly was a 3 hour learning experience. Make sure you have all the wires hooked back up BEFORE you hook up the motor mount clips. When you seat the motor on the mounts the wiring hookups need to be almost on the bottom. Check the instructions drawing for placement.
You don’t actually remove the fan cover you just unscrew the mounting screws and push it to the side.
Re-hooking up the belt and belt tightener is not intuitive but you will eventually figure it out. I found some generic dryer belt installation drawings on the Internet that showed me how to do it.
The photocopied instructions that come with the motor are kind of fuzzy after a few generations of photocopying.
In the end, it worked! It is also much quieter now.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

I removed the old door catch by using a screwdriver to pry it out, then I popped the new door catch in its place and it snapped right in. It took less than 5 minutes to do the whole job.

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.