1106307640 Kenmore Dryer - Instructions

same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.

Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!

I googled the problem, then came across a site where somebody had experienced the same problem, and they changed the door catches to resolve it. I did a search for Whirlpool parts and found "partselect.com". I followed the instructions on the website and located the parts very easily and also discovered that there was a video on how to make this repair. We were tolerating this problem for quite some time and now the problem is resolved, thank you...

I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.

i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.

This was a classic easy repair and I am sure saved us bundles on a service call.

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.

The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen the two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.

I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!

I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.

I removed the old door catch by using a screwdriver to pry it out, then I popped the new door catch in its place and it snapped right in. It took less than 5 minutes to do the whole job.

First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in about 10 minutes.