1106718500 Kenmore Dryer - Instructions

Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

Used the dryer illustrated parts list to find the heater. Used a multi-meter to determine that the heater had no resistance, meaning it was open and could not heat. Removed the heating element held to the dryer with one hex screw with a wrench. Purchased a replacement heating element and received it within 2 days. Screwed the new heating element with a hex wrench again. The dryer works like new now.

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

Dryer was taking long time to dry cloths, electric bill seemed higer than usual, used 1/4" nutdriver, removed rear panel, opened top cover w/screw driver to pry with, marked all wires with blk tape to id them later. Did thorugh inspect/clean of link section to propeller baleds 1 hr, continuity check of heater, switches etc found heater lower than spec, ordered heater, continued to clean all sections & vents, installed new vent hose, pulled about 2lbs of sand, dust, lint from all sections, heater works great now, clothes dry quick. New heater core came in mail and installed it. The newer elecment was 5200 watts, orig was 5400 watts, ohms was same, size etc. The unit works like a charm. Notes:Did not check or lubricat the drum. Drum is very squeaky, belt in good shape. Dryer is 20yrs old. Will replace when I can afford it! for now I can live with some sqeaks, anyway as I am getting older my hearing is going away, Good luck.

After watching the U Tube video to replace flywheel, I had a appliance repairman come to my home to install flywheel. There was no way I would have been able to put the dryer back together without some help.
I want to say "Thank You" to the sales representative who assisted me when purchasing my items, she was very patient while running around the house looking for the model number of the dryer.

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

Pulled out the old element (by removing the two screws that hold it in place) About a couple of inches and disconnected the two wires. I then inserted the new element and screwed it in place and connected the wires. Just took two of us to fix the problem...one to tilt the dryer forward and the other to put in the element.
I am so happy I didn't have to go out and purchase a new dryer........new ones are way too expensive!

just replaced parys

removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business

Replaced lid switch, but problem still continued.

I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair

Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.