11079082990 Kenmore Dryer - Instructions

I simply followed the video and apart from a couple of areas that were not relevant to my model, everything went exactly as illustrated. The video is excellent and made the repair so easy.

The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back and two in the front.

A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.

It was an easy fix, I just did half the install a second time.

had to take front off of Dryer then was able to replace drum roller

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.

Just like the video, just followed the video
Thanks,

Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum, let sit a few minutes. Put everything back together.

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pulley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.

After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.