1103402243 Kenmore Dryer - Instructions

Pulled out AC cord from wall socket first! Removed the dryer door and front panel (2 screws each) Then pulled both wire connectors off 2 coils. Removed hold -down bracket over coils. Replaced both coils and reconnect . No need to replace electronic igniter for gas. The right parts were shipped faster than I expected. Easy job. The Maytag repairman remained unemployed once again!

The gas would light briefly then go out so the clothes were never heated. I googled the problem and found your website and read a few blogs describing the problem, ordered the coils, popped them in and presto it worked.

I replaced gas coils which in my case came as a set and that did the trick.

Undo 2 screws take units out, clean a little, install new parts and screw down, done, great site !!!!!

Pried the top up, disconnected the door switch, removed two top screws holding the front panel, disconnected the spring and removed the front panel. Removed the screws and retainer holding the coils, replaced both coils and reversed the process. This was the third component I replaced to solve the problem....a cheap multi-meter and some testing would have solved the problem sooner. We now have the whole heat cycle.

The repair went very smooth. I was able to follow the directions on partselect and had the repair done in 15 minutes. I took extra time to test the continuity on the ignitor and fuses. I also used the shop vac to clean out the inside of the dryer. The best part I liked about this web-site is the fact that once I described the problem I was told that the "M" series style coil was the fix 90% of the time! $27.70 including shipping was all it cost to make my clothes dryer work like it did the first day we got it!!

Wouldn't have had a clue how to gain access to the coils without online instructions. It actually took longer to open the front of the unit than it did to replace the parts. Following the online instructions I removed two screws under the lint trap door. I then used a stiff putty knife under the left and right front corners of the lid to release the top, which I tilted back. Per the instructions I easily located the two screws releasing the front of the dryer. You have to lift the drum a bit to release the front panel. Once removed I was able to remove and replace the failing coils and then reversing the steps to put it all back together. An easy job and the dryer is back in shape.

All went very easily

unscrewed the 2 screws holding the coil's in place took wires off one coil at a time tested coils with ohm meter found the two wire coil was bad replaced and scered the bracket that holds the coils back in place.PartSelect gave me a list of what was causing the problem and what the % of what was the cause,this helped alot Thankyou PartSelect

I'm a 65-year-old woman with no prior appliance repair experience. I learned on the web that 30% of the time, the failure-to-heat problem is caused by the valve coil, and 30% of the time, it's the cycling thermostat. So I ordered both parts. I watched installation videos on the web. The valve coil was accessable through a front port on the dryer so I started there. I had to go buy a stubby screwdriver because access to the screws was limited. From there, it was easy to take out the old valve coil and install the new one. Just 5 minutes. I plugged in the dryer again, turned it on, and it worked.

First I opened the front of my dryer panel to see when the dryer was on if there was any gas flowing. I found that the ignitor was glowing , but no gas was releasing from the valve. So I figured that that is the root of the problem. I changed the old gas valves and replaced them with the new ones. It worked!! The whole process didn't take more than 30 minutes.

First, unplug power. The coils are easily accessible from the front of the dryer. Use a 5/16 nutdriver to remove two screws at the bottom of the bottom panel and lift the bottom edge of panel toward you. Pops right out. The assembly with the coils is on the front left. Use a small phillips to remove the coil-retaining bracket. Keep track of orientation of which coil goes where. Slide the suspect coil up off the column and slide the replacement in its place. Carefully slip off wire clips from old to new coil. Repeat for second coil. Reassemble and test.

Followed the easy instructions on the video, and it worked. Sure beats calling a technician.

Need a short handled phillips screwdriver. Unplug dryer from socket. Remove two screws near the bottom of the front panel. Swing the panel to one side so electrical wire doesn't need disconnection. Remove two screws holding bracket over the two coils. Unplug both coils. Plug in new coils. Replace bracket. Replace front panel. Plug machine back into electrical socket. Problem solved.

Replaced igniter