1106507802 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ernest from Moundsville, WV
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Wife pulled bed sheets out of drier and broke door switch actuator
Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Conway, AR
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer stopped working
The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen the two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.
Advice: Don't slam the dryer door. The actuator will last longer.
Advice: Don't slam the dryer door. The actuator will last longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- P from Melbourne Beach, FL
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door latch broken
Repair was straight forward with only two screws to undo. Popped the two sides in and I was done. What was amazing was the lowest cost on parts and the timely delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felipe from Helotes, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door would not close
Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Perkasie, PA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
replace the latch
take the old latch out and pop the new one in. Your repair kit worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sally from Houston, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch not working on Kenmore dryer
The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KRISTIN from DENVER, CO
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dryer door wouldn't stay latched shut during cycle
In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Millinocket, ME
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not latch
I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Tonica, IL
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Couldnt get the dryer to turn on even when i had power.
Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Colby, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My dryer door would not stay shut.
I removed the old door catch by using a screwdriver to pry it out, then I popped the new door catch in its place and it snapped right in. It took less than 5 minutes to do the whole job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Phoenixville, PA
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the door switch broke, and I had to pop the lid unscrew the switch and use a clothespin to depress the switch acuator button....not pretty.
same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Midland, MI
- Parts Used:
- 279827
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
dryer would shut off, make tons of noise and then wouldn't start at all
My husband figured this would be an easy fix....until he realized the part he had turn to remove the motor was made of plastic and was basically welded to the fan, so needless to say, we are now also replacing the fan....once the fan was loose, it was very easy to put in the new motor and fan and reassemble the dryer...good luck and watch out for those plastic moving parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hayti, MO
- Parts Used:
- 279827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Making loud noise, then will not run
Read earlier posts on the change out of motor with times varying from 30min to days. My ordeal was in the days category. Long story short, I could not get the blower off. The back of the blower has flats to use a adjustable wrench and you can use a socket on the back of the motor. I rounded off the flats on the blower and had to cut it off. Since I had only ordered the motor, I had to then order blower. If you can get the blower off the motor is about a 30min to 1 hr job. I would suggest purchasing the blower along with the motor to save some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Rockaway, NY
- Parts Used:
- 279827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Wrench set
motor stop working
i did not do the repair but when my friend finish it was great, this company is great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Bassett, VA
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would not come on
Replaced the cap over the door switch so when the door closed the switch was engaged
Was this instruction helpful to you?
Thank you for voting!