11086379620 Kenmore Dryer - Instructions

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?

Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.

Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping

Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!

After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and although not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!

Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.

I removed the two screws on the top by the lint catcher. Then, per information from this website, I pried up the top. I reached down into the dryer and removed the two screws on the broken door switch and replaced it with the new part. I am a recently widowed, 55 year old and was thrilled to find good advice, information and instructions on your website!! Simple as could be!

I followed your short video and found it very easy to do

Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.

Followed Youtube video - quick & easy

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.