1106617702 Kenmore Dryer - Instructions

This was a classic easy repair and I am sure saved us bundles on a service call.

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

very easy

Screwed in light bulb and glass protector

The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!

In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!

Unpluged power cord.removed top and front pannels(after disconnecting wiring to door switch.) Removed drive belt to drum,and removed drum. Checked and marked motor wiring before disconecting from motor.Removed motor,After unscrewing the blower from shaft.(Had to remove jumper wire from motor)Reinstalled the blower and secured the motor,reconect wires to motor.(rechecked wiring connections)Put back the drum,drive belt,and the front door pannel.(reconect door switch wiring)then the top pannel.Plug in the power cord and checked opertion.....WORK'S JUST FINE! I ordered the replacement motor on a sunday,and the new motor was setting on my kitchen table tueday afternoon when i got home. Great job" PARTSELECT."

Replaced the cap over the door switch so when the door closed the switch was engaged

I took the back off of the dryer and then removed the lint chute assembly. Next came the top removal which was a little tricky because the top locks were installed incorrectly from factory. After about 20 minutes for a 2 minute job, the top came off. Now I was able to remove the front and the drum. This left me access to the motor. The hardest part of the whole job was removing the blower wheel. Being made of plastic you must be careful not to brake it while grabbing hold of it and applying torque to the motor side. This process takes two people. My wife helped me and it took about 5 minutes. Leave the motor mounted for this. Once the wheel was off, the motor was then removed, the new one was installed and the process was reversed for assembly. Not very difficult overall and saved me a whole lot of money. Make sure you vacuum out all of the dust since you have the whole dryer apart. It will probably be the last time you see inside it and the dust sure builds up inside after 12 years! Thank you Partselect!!

I read several customer feedback articles to find one with problem similar to mine. After eliminating the thermal fuse, it was obvious my motor was bad. Watched the video and easily removed motor. Took motor to a repair shop and they confirmed it was bad. Replacement motor arrived in two days (yes...2 days). Unbelievable quick delivery. Easy to reinstall---only took about an hour. Hey, it would have cost $500-$600 to replace this dryer! Now I feel like I have a new dryer for $80!

First I removed the rear panel of the control sectio and the main rear panel. I checked the switches and fuses. The fuse for the dryer vent was giving an intermittent signal, so I replaced it with one I picked up at a local repair shop.
Since I had started working on it, and due to the age, I went ahead and ordered a motor, belt, and drum rollers and replaced these as preventive maintenance.
Once you realize how everything comes apart, it is not a very dificult job to overhaul the complete dryer.

Was informed that I had a bad dryer motor and no warranty. Unplugged the unit. Removed to screws in the lint trap slot. Used a small blade screw driver to pop the 2 clips at the front of the dryer top. Lifted the top and rested it up against the wall. Removed 2 screws holding the machine front panel. Removed the front panel and removed the tub. Couldn't get the blower loose from the dryer motor so I cut it off with a hacksaw. Moral if you are going to replace the motor go ahead and by the blower too. It is less than $20.00. Popped 2 clamps loose holding the motor in and removed it. Placed the new motor in the unit. Strapped it down and attached the new blower. Plugged it in, put the dryer back togehter and tried it. It worked.

Repair was simple, minus pulling the drive motor shaft out of the back fan. The female end of the dryer fan was made of plastic, so the socket wrench cracked the plastic end. Other than that, the repair was simple and easy to do. Much better paying the $88 for a new motor vice paying $400 or more for a new dryer. Dryer has run like a champ since replacing.

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

My husband figured this would be an easy fix....until he realized the part he had turn to remove the motor was made of plastic and was basically welded to the fan, so needless to say, we are now also replacing the fan....once the fan was loose, it was very easy to put in the new motor and fan and reassemble the dryer...good luck and watch out for those plastic moving parts!