10688419300 Kenmore Dryer - Instructions

I checked the Thermal Fuse and it was okay. Then I tested the timer and it was not working. Then I ordered the timer from this site and installed it in about 30 min. The dryer is now working.

Unplugged dryer, unscrewed back, and replaced fuse. Easy as 123. Video showed what to do step by step! I am not a handy man, just a woman trying to be money5 smart. Anyone could do this and save on home repairs.

I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.

Once again part select has come through for me. googled dryer won't start and a video on utube came up. typed my model number in on part select website and followed directions. was easy got part in three business days regular shipping. very pleased with this site.

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!

Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

Unplugged stove . Removed floor of oven . Easy . Removed the ignitor ,near back of stove under removed floor . .Left it in place to enable locating where wire came through back of stove . Pulled the stove away from wall . Removed back panel of stove . followed ignitor wire to its plug in position . Returned to the front of stove . Inserted new ignitor wire through back wall of stove . Went behind stove , pulled wire through enough to plug new ignitor into proper position . Put back panel onto stove . Pushed stove back against wall . Went back into oven to screw new ignitor into place . Replaced oven floor panels . Put cooking racks back in . Wife proceeded to bake once again .

Went on line and determined the problem was the thermal fuse. Removed the rear panel of the dryer, removed the leads from the thermal fuse, hooked them together and started the dryer. That confirmed the problemwas the existing fuse.Ordered the new thermal fuse, installed the fuse, hooked up the wires and it works finel Very simple fix. About a 10 year old dryer.

Checked on your website for common problems w/this model dryer,highest probability was the thermal fuse being blown,so I ordered one & checked the vent for being plugged,no problem there,removed the back of the dryer replaced the fuse(very easy to do)put everything back together & started it up...all set now.Thanks for your help

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

I watched the video several times before beginning, which was very helpful. As I didn't have the tool that was recommended in the video, I used pliers, which although took longer, worked out fine. I also used pliers to pull the wires off of the old thermal fuse. My dryer had been not working for 2 months, so I was very pleased that I was able to watch a very detailed video, order the parts on the same website, and receive them very quickly (within couple of days.) My daughter who lives in another state googled my dryer model number with a description of the problem and found your website. She sent me the link of the video to watch as it appeared very easy to understand. She and I both were very impressed by the step-by-step instructions on the video, including a list of all the tools required. I am an 81 year old woman and had no problems fixing this by myself with the assistance of your website. I have recommended this site to several of many friends and family members. Thank you!

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).