1105907720 Kenmore Dryer - Instructions

very easy

I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. almost spent $400.00 on a new one.

Neither the washer or the dryer of the stacked unit would start. The website suggested that one of the causes could be the thermostat. I ordered a replacement that arrived quickly. Swapping the part only took minutes, and it started just fine.

I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.

This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

I removed 2 screws to the lint trap, popped top of dryer with a flat screwdriver but did not remove it I just raised it and leaned it against the wall. I removed 2 screws from the top of the inside front panel,then I hooked the new cables to the springs that are on either side of the front panels at the top. I then pulled the panel forward just enough to fit my hand and thread the cables through the holes that are on the front panel that lead to the door, I had already popped out 2 plastic caps that go inside the door on both sides.I then treaded the cables inside each hole and snapped the caps back on. Iris

Removed back cover of entire dryer.The thermostat was accessible from that point(Just as diagram showed), removed two wires from thermostat, removed thermostat & replaced with new thermostat & plugged 2 wires back in just as instructions indicated. Very simple,15 minute job. I will certainly use again for any appliance repairs.

always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James

Removed the old one installed the new one

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.

After removing the front of the dryer it was evident that the blower boss had broken where the motor shaft comes through and is attached. I removed a few more parts to make the blower more accessible and removed it. I then machined a new boss and attached it to the blower and reinstalled it.I then did a quick continuity check on the three thermostats since the dryer was already apart.I discovered one was faulty and ordered a new one from you.That repair took all of five minutes.The irony of the whole thing is that while I was ordering the thermostat from you,I asked out of curiosity,if the blower was still available. As it turns out it still is but the new machined part worked out great and the dryer was back up and running in no time.

Thanks again,
Dave

ordered wrong limit switch had to reorder right switch and decided to replace the heater element as well. works fine now

replace the water valve

Took the back off the dryer. Disconnected the old thermostat and installed the new thermostat. Connected the back of dryer. Put in a load of clothes to dry and the clothes were dry on the first try. Works like a new dryer. Saved a lot of money not having to buy a new dryer when all I had to do was replace some old parts.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.