1106958701 Kenmore Dryer - Instructions

all that was required was to push the catch into the slot notools needed.

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.

First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

Removed top, then remove front panel, then removed the drum, and the idler pulley assembly. Then added new parts, and reversed procedure to assemble back to new.actually runs better, now. Dryer is approximately 30 years old.

watched your video on 'how to' and did it like man showed..no problem

the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.