1106407501 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- charles from bryan, TX
- Parts Used:
- WP694674
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
low or no heat
Removed back cover of entire dryer.The thermostat was accessible from that point(Just as diagram showed), removed two wires from thermostat, removed thermostat & replaced with new thermostat & plugged 2 wires back in just as instructions indicated. Very simple,15 minute job. I will certainly use again for any appliance repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- barbara from san diego, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
door catch broke off
just the way the video showd me
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Iota, LA
- Parts Used:
- W10820036
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Dryer door switch broken or burned out
My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.
Was this instruction helpful to you?
Thank you for voting!
Door hinge, cable, and fastner needed replacing.
I followed the instructions from your sight mainly with a alteration.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryanne from Deptford, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer door would come open when running
Followed instuctions on video accept our appliance was the Duet HT model so we had a glass window to deal with. Just a few more screws to keep track of but otherwise a very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Thomasboro, IL
- Parts Used:
- WP694674
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
no heat
ordered wrong limit switch had to reorder right switch and decided to replace the heater element as well. works fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Sussex, WI
- Parts Used:
- 279570
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The dryer door catches needed to be replaced
I watched the video provided first to get an idea of how it should go. The dryer I have had a different kind of door, so those instructions didn't apply. You probably don't want to publish the way I ended up fixing it, but it did work eventually. Saved me over $500!! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronnie from meriden, CT
- Parts Used:
- W10820036
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
over fill water
replace the water valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tomas from Orlando, FL, FL
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broken
Removed the old one installed the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from North Chesterfield, VA
- Parts Used:
- 279570
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic catch broke
little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Kingston, MA
- Parts Used:
- WP694674
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
A lot of noise coming from the front of the dryer.
After removing the front of the dryer it was evident that the blower boss had broken where the motor shaft comes through and is attached. I removed a few more parts to make the blower more accessible and removed it. I then machined a new boss and attached it to the blower and reinstalled it.I then did a quick continuity check on the three thermostats since the dryer was already apart.I discovered one was faulty and ordered a new one from you.That repair took all of five minutes.The irony of the whole thing is that while I was ordering the thermostat from you,I asked out of curiosity,if the blower was still available. As it turns out it still is but the new machined part worked out great and the dryer was back up and running in no time.
Thanks again,
Dave
Thanks again,
Dave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Manlius, NY
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door latch broken
For 2 years, I propped a broom stick against my dryer door to keep it shut while it was running. Last Sunday night, I decided that it was about time to fix it. I found the PartSelect site, which was extremely easy to navigate, and ordered a replacement kit. It arrived in 2 days via Fed Ex and actually contained extras of each of the 2 components, in slightly different sizes. It took me about 10 minutes of eyeballing the parts to figure out how to place them and about 30 seconds to install the new latch parts. They fit perfectly. Great site, great service, I would highly recommend this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Yankton, SD
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door would not stay shut
Got the latch kit, found the correct one, popped it in...dryer works! Thanks....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leah from Philadelphia, PA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door would no longer catch when shut
Having read the instructions and watched the tape, I pried out the remaining catch with a flat screwdriver, read about what the color scheme on the parts wasbout and pushed in the correct part. Voila ! Done in probably two minutes.(By an 82 year old woman!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent A. from Gibsonia, PA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The catch on the dryer door had to be replaced
Six(6) screws were removed to separate the front and rear sections of the dryer door to get access to the rear of the catch.Pliers were used to maneuver the catch through the opening in the cabinet from the rear. The new catch was easily snapped into the catch opening from the front of the door.
Was this instruction helpful to you?
Thank you for voting!