11097094700 Kenmore Dryer - Instructions

Remove old filter
Vacuum out
Install new filter

turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Ezee pezee lemon squeezee.

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place located just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.

You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...

Remove top,front and panels.change thermal fuse and outlet thermistor.

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.

all that was required was to push the catch into the slot notools needed.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way. The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.