1106508821 Kenmore Dryer - Instructions

I looked up my paperwork on the dryer and found out how to remove the proper panel to get to the inside of the door. (I was able to find the manual on the internet also).

I cleaned all the dust while I was inside. The actual repair of the broken parts took about 5 minutes.

Parts received were exactly like the broken ones.

Thanks Parts Select. Saved me $139.00

John

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

I followed the video. So easy..

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Pull out the old lint filter unit; push in the new one.

Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

Opened new package took item out and put it on the slot where the old filter was. Easy as pie. My dryer is 46 years old and works just fine.

Ordered a correct part # lint filter from this site, removed old filter & installed the new, very simple fix.

Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place located just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.

When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked up the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.