11088390730 Kenmore Dryer - Instructions

my hany man did it....

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

I followed the video. So easy..

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

Excellent and super easy. Owned the box and snapped the new one in. Ready for laundry again in a matter of minutes.

Replacement fit perfectly.

Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.

I would not ever consider this a repair. The dryer filter cracked because of my wife put it in loosely. The new one just fit right in.
What was so good about the entire process was how quickly I recieved the part. A matter of two days.

Didn't need a repairman for this project! Ordered the part (seems like on Sunday) and got it really quick (the next Wednesday). Opened the package, placed the part where it was supposed to go and shazam!!!! Fixed it was quick and easy!

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

all that was required was to push the catch into the slot notools needed.

You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.