1106408901 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JERRY from SPANISH FORK, UT
- Parts Used:
- WP95292
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old tube burned out
removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Laingsburg, MI
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door wouldn't fasten shut
Popped the latch out and popped a new one in.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Ramsey, MN
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Received part in 3 days from ordering. I was surprised when it showed up at my front door so quickly. Less than 1/2 hour later we were drying laundry again. Very impressed with the speed of service and the price.
First removed 2 screws on lint remover vent. Used a screw driver to force up top of dryer from out front. These will require pressure to pop the top off the dryer. Once the top was up I could reach the actuator and remove the 2 screws holding it. Once removed just replaced with new actuator and bam, done. Snapped top of dryer back on and reinstalled 2 screws on lint vent and Done. Easy, no problem....Thank you PartSelect!!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Cumberland, RI
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door wouldn't shut
The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Chhicago, IL
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The male part of the door catch was broken
Simply installed the piece and I was done. Took 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Thompsonville, MI
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door catch wouldn't hold the door closed
I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Big Timber, MT
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door kept opening
Popped out the old door catch kit and replaced it with the new one! Easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Terre Haute, IN
- Parts Used:
- WP691581
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
dryer latch engagem ent
our son was able to diagnosis and order the part and very pleased with quite response. Dryer now working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Phoenix, AZ
- Parts Used:
- W11613302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door Gasket Broke into pieces
It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Nanuet, NY
- Parts Used:
- W10820036
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
washer would fill with water but not start
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andris from Sands Point, NY
- Parts Used:
- W10820036
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Dryer would not activate
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Bassett, VA
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would not come on
Replaced the cap over the door switch so when the door closed the switch was engaged
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Elmhurst, IL
- Parts Used:
- WP691581
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washing machine over 20 years old but still runs strong door switch actuator spring broke original spring was not availible.
drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margery from Lake Spivey, GA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the door catch was broken and I was using duct tape to close the dryer!!
This was a classic easy repair and I am sure saved us bundles on a service call.
Was this instruction helpful to you?
Thank you for voting!