1106118254 Kenmore Dryer - Instructions

Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.

take the old latch out and pop the new one in. Your repair kit worked perfect.

In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

Replaced the cap over the door switch so when the door closed the switch was engaged

Fantastic site and service !!! Using your site, I i'd my needed part in about 10 minutes. I received my Whirlpool dryer door latch part from you in less than 12 hours. Per your internet site instructions, I replaced the part in a few seconds (just popped it into the slot) and my wife had a working dryer for her Sunday wash. I would have been out $55 and 4 to 7 days waiting for a service call if I had used my home warranty service contractor. Using your service, the part(s) and shipping were just over $12.

ordered new latch kit and repaired, very easy thank you

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you

Took 5 seconds, just snapped in the slot, didn't need any tools.

Snapped latch into existing hole in 2 seconds. The pin that goes into latch was still intact. That's it ,real simple. The only problem I will hopefully not have in the future is the the mico-switch which is just hanging in there, the switch works but the lever that extends out from the face, that works with the door is partially broken off and the switch is no longer available on your parts list. The appliance is twenty-one years old. I am very happy with your service and I received the parts the next day, after I ordered them and I will be buying more parts in the months to come. This time it will be for my Kenmore gas stove and then a Kenmore refrigerator door hinge.

two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clothes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened