11076873200 Kenmore Dryer - Instructions

I looked up my paperwork on the dryer and found out how to remove the proper panel to get to the inside of the door. (I was able to find the manual on the internet also).

I cleaned all the dust while I was inside. The actual repair of the broken parts took about 5 minutes.

Parts received were exactly like the broken ones.

Thanks Parts Select. Saved me $139.00

John

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

This model top can be popped off after removing the two screws under the lint filter. Once exposed remove the old cables and feed them through the hole on the front panel. Feed the springs through the ends of the cables and hook the other end into the dryer side panel slots towards the top on each side. Once both cables are fed, feed the opposite ends of the cables into the slots in the dryer door (after popping the white plastic covers out of them first). Put the white covers back into the slots to hold cables into doors. The door catch kit install is pretty obvious.

Like others have descibed, place Dryer on back and remove two hex head screws on back two phillips screws under lint cover, front is "clamped" with two plastic clips that I popped with a standard screwdriver. The door has two screws on the door switch, I removed these although I'm not sure I needed to. Lift the front out of the way. Look at the belt before you remove it, the tensioner pully isn't screwed in place and drops once the belt is removed. It isn't hard to figure out how it goes back together, but you might as well save the swearing. Remove the belt and the drum lifts out. Remove the old seal and glue the new one in place. Another repair suggested clothes pins to hold the seal while it dried, but I opted for some spring clamps with a little more grip. While the seal dries vaccuum the inside of the dryer and vent pipe clean everthing up good by the time you're done the glue is dry. Put the drum back in using a putty knife to slip the seal in place. re assemble in reverse order of disassembly. If I were doing this repair again I would have bought the front seal too. It doesn't appear to get as much wear as the back, but while you have it open why not? Repair easier than expected, but took more time with the cleaning and glue dry time.

Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.

1) removed the old broken filter
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!

As the instructions say: first remove the drum. In the case of my dryer the drum is supported by two rollers on the back panel and the opening in the front panel. Remove the front panel and the drum almost falls out.

Replacing the seal was easy . Just tear out the old seal, lightly sand the rear lip, stretch the new seal over it, being sure the stitching is oriented properly, and then squeeze adhesive from the supplied tube between the seal and the drum lip.

In putting the dryer back together I couldn't figure out how to thread the belt. I suggest that people attempting this repair take digital pictures of the inside of the appliance before disassembling it.

A very good experience and I prolonged the life of the dryer a good ten more years.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

i took the old knob off, went to partselect and ordered the part really easy as their site helped me find the correct part, and put it on with ease when it came in the mail. It works great and PartsSelect helped me be a hero to my wonderful mom. Thanks.

Changed out the lint filter

Just put the knob on where old knob was.

Took the old one out, replaced it with new one.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Timer knob.....took new knob out of protective shipping bag and installed it on the existing timer stem. It took less than one minute.

Door catch kit......removed original female latch part from dryer door and installed new one by pushing it in the hole left by the original part.