11088722892 Kenmore Dryer - Instructions

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

Hi, I am a working mom, and my dryer quit just after it had been behaving strangely. At first, it kept spinning after the door was opened. It eventually stopped working, and I assumed that the door switch must be the culprit. I purchased the part from the catalogue, and watched the installation video. Repair: After unplugging the dryer and removing the lint screen, I used a philips head screwdriver to loosen and remove the two screws located at the lint trap. I then inserted a flat screwdriver into the area between the top of the dryer casing and the face. Per the video, at approx. 2 inches in from the left and right side. I did this while gently applying pressure from the back of the dryer top to the front. This loosens the clips allowing the top to be lifted back and out of the way. I then opened the dryer door and commenced loosening and removing the two screws that hold the dryer switch in place. I used my screwdriver to gently separate the wiring harness connection, as it also has a clip to keep the connection tight. With these items free, I simply popped the little black thingy back through the hole (The black thingy just keeps the slack in the wiring from sagging, I think). With the old part removed, I then installed the new part accordingly. I reversed my way back out of the process respectively. I plugged her back in, and turned her on. Back in business.

First and foremost turn power off to dryer at main box. Next remove screws say lint filter, then gently pry right and left front corners up with putty knife. Raise top and secure. Disconnect switch wire by using flathead sliding in between connection. Next remove 2 screws under front opening to dislodge switch. Repeat process in reverse order...takes 30 min. tops...

replaced internal dryer filter housing

Well turned off power by unplugging it. Took a Phillips screwdriver and took the 2 screws out from vent and then took a flat head and left up each side to access the inside of dryer. Then used screwdriver to take out screws to switch and then disconnect the power cord to that. Reverse the procedure and it was so simple. Ty. Awesome company.

Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

Disassembled dryer, removed tumbler, replaced drum support rollers

I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.

Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.

From the front, taped part in place and then assembled springs and insulator from the rear. Difficulty occurred with access to the back of the sensor due to the air duct interference. The sharp edges of the sheet metal parts increases the risk of cuts. First shipment was missing the second electrode but Part Select immediately replaced the shipment. My experience has to be considered Excellent and I would go to Part Select first for my next order.

Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.