11086581110 Kenmore Dryer - Instructions

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

Undid the back, remove wires going to element, unscrew lint trap, pop the top and undid the nut-screw holding the element housing. pulled out the bad element and did everything in reverse with the new element... unplug it first though because I left that step out.

Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.

The repair was really easy and I loved the DIY videos they were great, not many tools needed to do these repairs that was great. The only thing is this didn't solve my issue.

First disconnect power supply either by switching off breaker or unplug dryer cord, or do both if you are a safety freak. Pull dryer out so you can get to the back panel. Take the dryer hose off, then take screws out from around panel and remove it. For the THERMAL FUSE take one screw out, unplug wires and replace thermal fuse. For HEATING ELEMENT, unplug the two wires from element. At top of air duct there is one screw to get out. You need a long flat head screwdriver. Reach through a small hole on dryer back to the screw. Once screw is out, lift up on air duct to get it out. Once you have it out there is one screw holding heating element in air duct. Remove screw, slide element out and reverse steps from when you took it apart to put it back together.

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

Unplug the dryer and remove the back panel. I lifted the top of the dryer for easy access to the screw that held the Heater Box. Removed the Heater box, unbolted the heating element, pulled the old one out put the new one in the reversed the process.

I ordered the part Saturday, had it by Tuesday.

i took the old knob off, went to partselect and ordered the part really easy as their site helped me find the correct part, and put it on with ease when it came in the mail. It works great and PartsSelect helped me be a hero to my wonderful mom. Thanks.

Just put the knob on where old knob was.

removed 5 screws holding back cover on. Oh yeah very important (that is if you'd like to be around to help your buddy do this) unplug the unit 1st!
Accessed the heat coil. Difficult to remove the element so opened top of dryer to access the screw that was on top of the housing was then able to easily remove the element and replace with the new one. Actually, removing the top of the drier was a very good thing because it gave me a chance to throughly clean out any lint. but number one reason was I found the drier door cutoff switch wire had come loose from its clip and was laying on top of the drum and slowly grinding the insulation off the wire! had not shorted yet but would have failed soon.
anyway... I got cheap when buying the parts and didn't buy the real part that was bad... (lesson learned) anyway found the parts I did replace were not bad. So back to the net again to order the last thermal limit switch and fuse. received the parts 3 days later installed them. Now life is good! Well at least dry warm shirts and socks! Decide to keep the extra parts just in case I need them down the line.
Actually even with the problems encountered "I" still repaired the drier myself saving big bucks and enjoyed the small but fulfilling challenge!
Excellent experience working through partselect.com

Changed out the lint filter

Removed rear panel, removed 3 screws and old element and installed new element. To install new element I only needed one screw and spliced in the two wires that were provided with the element. This repair was simple and now the dryer works great.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.

After un-plugging the frig and allowing it to defrost, we emptied the frig and gave it a thorough cleaning inside and outside. I then removed the shelving in the freezer and the face plate at the back of the machine. One of the defrost heater coils had burned out and there was a loss of continuity which was keeping the frig from defrosting properly. The old heater snapped out easily. I went to this website and ordered a new defrost heater assembly which arrived practically overnight. It was identical to the old one and installed as quickly and easily as the original had come out. I put the faceplate back on, put the shelving back in, placed a thermometer inside the fresh food section, plugged it in and waited until I heard ice cubes drop. The fresh food section was holding at 41 degrees F which is optimum. The refrigerator has been working smoothly every since! Easy job!