11088724891 Kenmore Dryer - Instructions

I was hopeful it was the belt. But, I had no idea how to get to it. I used the model no. and looked on line for pats and schematics. That gave me a sense of what to do. I started at the rear and removed the back panel. It was like peeling an onion because then, I wasn't sure what to remove next. So I just kept removing nut head screws until eventually I had loosened the sides, removed the top and discovered the front lifted up and off (no screwed attachment.) There's grounding wire that must be detached. Don't forget to re-attach. Without proper grounding you could be electocuted! I was careful to remember how it was attached. To get to the pulley, which is on the front, I had to remove the drum. I found the snapped belt. The pulley is held in place by tension from the belt so, once the belt goes the pulley detaches. I tried to find the belt locally the following week but was unsuccessful. I found the part on-line and had it in four days. It was tricky getting the belt and pulley in place. I persevered.
The parts ( I replaced the fliter that needed replacement for years too) came with installation instructions. Its possible I did not have to disassemble as much as I did. Oh well! Although I'm fairly mechanical, I'm still pretty proud to have been able to do it and save the cost of a repairman.

We were able to look at the diagram of the dryer to figure out how to access the part and then replace it. Fantastic! Your site is wonderful. The suggestion for the repair for not starting was right on the mark. The parts came very quickly, as well.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!

NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.

First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to glue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!

Came to Parts Select. Looked for door switch. Read what other people did. Part came in a few days took a few minutes to take old switch out (had to pry the plastic connection apart with little thin screwdriver). Everything was easy

First unplug dryer, then remove 4 screws along the back of the top and remove top and set aside. Next pull outward on the front until the front clears the drum and lift off the front and set to the side, careful not to stretch the wires to the door switch. Remove old belt and slip belt around the drum and line up with marks from old belt. Reach in under the drum under the motor and lift up the tensioner. Insert belt through tensioner and slip over the front of the shaft on the motor and release the tensioner. The belt should now be tight. Reinstall the front and top, plug in and test.

PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.

my dryer door didn't latch for over a year. We were accustom to proping large objects against it. a friend told me to look on line. The close up pictures and parts diagrams were awesome. It was here in 4 days . Now my family thinks I am a hero. The end

First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and replaced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.

Thanks Mike

I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.

one of ears that holds filter was broken leaving a small gap so lint went into duct work so i replaced the cover and filter is now held in place letting the filter do its job trapping the lint

When the problem first came up, I took the dryer apart without first looking up any instructions. This wasn't difficult, but didn't realize when removing the fan from the motor, there is a square lug as part of the fan hidden by the rear clamp securing the motor. I was able to remove the fan by holding the motor shaft with a crescent wrench and removing the fan by hand, but was difficult and gloves were necessary in case the fan loosened quickly and my hand came in contact with the sheet metal (very sharp).

I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.

This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.

The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.

I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.

installed according to directions, went well. However I recommend getting a newer dryer, it is 15 years old and didn't work all that well, even when fixed.