11076822693 Kenmore Dryer - Instructions

I removed 5 screws from the back of the top panel, removed the back panel, removed the start button from front of dryer, twisted the old start switch from the back, removed the two leads, reinstalled new part in reverse order. It was that simple! 15 minutes top. Dryer works fine. Gave me a chance to vacuum out all the dust bunnies and clean out the dryer vent pipe as well.
Thanks!

Removed top and front of dryer then drum and followed the instructions in the package. It was a real simple procedure. I did additional cleaning while the dryer was disassembled.

I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.

The dryer quit working. I did some trouble shooting on your amazing site, ordered what i thought it might need and then got to work. Took no time to get it apart and replace roller kit and belt. What took the longest was getting in there and cleaning out probably 15 years worth of dirt and dust. If you have not opened your dryer up and done this, 10/10 recommend, because in doing so i found that the motor was the real culprit. Once i opened it up more, especially cleaning around the blower fan and motor, i was half a day in. Put it all back together and got it running for two more loads before the motor quit. Replaced that and since the hard work was done, had it back in in half an hour and running great. Probably will need to redo the felt seal one day, but for now, i am calling it a win. This is my go to site for all things and i have been able to work on most of my major appliances and do it myself using the helpful information here.

pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.

Braced dryer drum with a block. Removed the two rollers one at a time by using a screwdriver to pop off the triangular clip. Slid on new rollers. Would have been easier to remove the drum out the front instead of bracing it. Installed new idler pulley and belt. Dryer is 25 years old and sounds like a new one now when running.

Dryer would not start when the start switch was pushed. I was advised by the local repair shop to replace the "push to start switch" and the "thermal fuze". I unplugged the dryer and removed the back dryer casing which took all of 3 minutes. I removed the start switch and thermal fuze using directions on the whirlpool parts forum. This took maybe 5 minutes. I replaced with the new parts and put the casing back on the dryer. The entire project took 15 minutes. The dryer works perfectly. 34 USD for parts and shipping instead of 600 for a new dryer. Easy to identify the parts needed using the model number and the parts arrived the next morning I will use this company again for sure!

with both hands

removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!

Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then he said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.

changed out the switch. easy. about 20 minutes. part came quickly (2-3 days). great service. thanks.

Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.

Once I started using a bunch of clothespins to hold the felt in place and then started gluing small sections at a time I was able to complete the task. The glue comes out of the tube very quickly so don't squeeze it a lot.

Getting to any of the parts in the Maytag dryer is easy. Tip the dryer back and slide a 4 x 4 block under the front edge. You remove the whole front panel after you remove two screws at the bottom corners of the front panel. You need to tip the dryer back to get a screwdriver on the screws. Swing the front panel up to release the top of the door panel from the top. Watch the short wires to the door switch. Unhook the door switch wires and move the front panel out of the way. The timer on the top is accessed by re-moving two screws along the top edge. There are four screws. Remove them all and tip the top of the front panel forward. You then see that two screws hold the panel and the other two screws just hold the trim.

The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.

I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).

First, I unplugged the dyer and then I removed all of the screws for the panel that covers the rear of the dryer. This exposed the cycling thermostat's location. I then removed the wires, one at a time so I would be able to put them back on in the same place. Then I removed the one screw using a nut driver and then put the new cycling thermostat in place. It was pretty easy.